Bedienungsanleitung Zenec ze 5 1 d (Seite 18 von 30) (Englisch)

167880

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

REMOTE CONTROL BUTTONS & OPERATION

1. Mute On/Off

When the amp powered on, the MUTE button on the remote control is used for instantaneous

lowering of the volume level to zero. Eliminating MUTE can be done by pressing the MUTE button

again, or else adjust volume up or down.

2. Input Selection

The INPUT SELECT button on the remote control provides manual switching of the input coming

into the system. The  rst press of the INPUT button displays the current input source. The

selection switches in order from -> Optical -> Coaxial-> Input1 -> Input2 and then back to Optical

again. Input switching is possible while the source is displayed on the screen. If there is an error

in optical or coaxial input, the display will blink continuously. In this circumstance, all controls are

available while blinking. The ZE-5.1D has source memory: When you power the unit off and then

on again, it will remember the last source selected, and return to that source automatically.

3. Test Tone

The ZE-5.1D amp features a test tone mode to check, if all speakers are connected properly. When

this button is selected (on the remote control), white noise of a fairly low volume is forwarded to

each of the 5 main speakers in order from -> Front Left -> Center -> Front Right -> Rear Right ->

Rear Left, alternating every 2 seconds until the button is pressed once more.

Note: There is no test tone for the SUB output.

4. Set-Up

This button causes the On Screen Display to open the menu for setting up the ZE-5.1D ampli er.

In this menu window, the selection, function, and control of the selected function sections can be

accomplished. The Set-Up menu allows control of:

• Pro Logic Selection

• Dynamic Range Compresion Selection for Dolby 5.1 material

• Crossover Filter selection for LPF and HPF used in Bass Management

• INPUT1 Level

• INPUT2 Level

• Channel level (input gain) control

Pressing the Set-Up button on the remote while the menu is displayed on-screen, will cause the

menu to hide. This button is also used to return to the main Set-Up menu from the channel level

control menu.

5. Menu Up/Down

When the menu is displayed on the OSD (On-Screen Display), the function to be controlled can

be selected by the Up/Down buttons. The buttons are set up in a circular pattern on the remote,

for ease of use.

6. Selection Left/Right

After the selection of function using the Menu Up/Down button, function-dependant values can be

changed using the LefVRight buttons on the Remote Control. As soon as the value is changed,

the new value is displayed without requirement of con rmation. For value changes, the left button

is used for decreasing values, and the right button is used for increasing values.

ZE-5.1D Manual E+D 27.02.2004, 14:32 Uhr18

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zenec ze 5 1 d Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info