Bedienungsanleitung Zenec ze nc514 (Seite 126 von 152) (Deutsch, Englisch)

163143

126

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Button Description

Closes the Cursor menu, and returns to the previous screen.

Zooms out the map.

Zooms in the map.

With the Cursor menu open, you can still move or scale the map, and tap

the map anywhere to place the Cursor to a new location, but when you use

this button, the Cursor jumps back to the place where it was at the time

when you opened the Cursor menu.

Displayed at the Cursor if it is at the same location with which the Cursor

menu was opened.

Displayed at the Cursor if it has been relocated since the Cursor menu was

opened.

Opens a new screen with the address and coordinate of the Cursor, and

the list of nearby POIs.

Opens the full-screen Cursor menu with all the possible options.

A new route is calculated with the Cursor as the destination. The previous

route is deleted.

If the Cursor is at or near the destination, this button replaces the previous

one, and deletes the current destination from the route. The last via point is

promoted as destination, or if there are no via points, the route is deleted.

The Cursor is added to the active route as an intermediate route point, a

point to be reached before the destination. If there is already a via point in

the route, the Edit Route screen opens to let you decide where the new via

point is to appear in the route.

If the Cursor is at or near one of the via points, this button replaces the

previous one, and deletes the selected via point from the route. The route

is recalculated without the deleted point.

The Cursor is appended at the end of the route as the new destination.

The previous destination is demoted, and becomes the last via point.

This button is similar to the

button, but a new screen

opens, and the route is calculated with all the possible route calculation

methods (Fast, Short, Economical and Easy). Observe the results, and

choose one of the routes to navigate.

The Cursor becomes the start point of the route. This means that the route

is not started from the current GPS position, and Automatic Off-route

Recalculation needs to be turned off to keep the selected point as the start

point.

If the Cursor is at or near the selected start point, this button replaces the

previous one and deletes the start point from the route. The current GPS

position is used again as the start point, and Automatic Off-route

Recalculation is re-enabled.

The Cursor is saved as a user POI. Select the POI group and give a name

for the POI, then select a suitable icon, enter a phone number, and

additional information if you like.

Map locations can be marked with Pins. Unlike POIs, a Pin has no name

and other details, only a colour to let you tell one from another on the map.

ZE-NA2000_UserManual_UK.indd 48 23.04.2009 10:43:16 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zenec ze nc514 Seite 126

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info