Bedienungsanleitung Zgonc YPL 1250 (Seite 14 von 32) (Deutsch, Englisch, Französisch, Italienisch)

781877

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

14 І 32

Notice!

Only low pressure is required for hammer drilling. Ex-

cessive pressure will exert an unnecessary force on the

motor. Check the drill bits at regular intervals. Sharpen

or replace blunt drill bits.

Maintenance

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

• Keep all safety devices, air vents and the motor hous-

ing free of dirt and dust as far as possible. Wipe the

equipment with a clean cloth or blow it down with com-

pressed air at low pressure.

• We recommend that you clean the equipment imme-

diately after you use it.

• Clean the equipment regularly with a damp cloth and

some soft soap. Do not use cleaning agents or sol-

vents; these may be aggressive to the plastic parts in

the equipment. Ensure that no water can get into the

interior of the equipment.

Brush inspection

In case of excessive sparking, have the carbon brushes

checked only by a qualied electrician. Important. The

carbon brushes should not be replaced by anyone but a

qualied electrician.

Storage

Store the device and its accessories in a dark, dry and

frost-proof place that is inaccessible to children. The

optimum storage temperature is between 5 and 30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust

and moisture.

Store the operating manual with the electrical tool.

Disposal and recycling

The equipment is supplied in packaging to prevent it

from being damaged in transit. The raw materials in

this packaging can be reused or recycled. The equip-

ment and its accessories are made of various types of

material, such as metal and plastic. Never place defec-

tive equipment in your household refuse. The equip-

ment should be taken to a suitable collection center for

proper disposal. If you do not know the whereabouts

of such a collection point, you should ask in your local

council ofces.

Old devices must not be disposed of with house-

hold waste!

This symbol indicates that this product must not

be disposed of together with domestic waste in

compliance with the Directive (2012/19/EU) per-

taining to waste electrical and electronic equip-

ment (WEEE). This product must be disposed of at a

Turning the handle clockwise will tighten the clamp. First

release the additional handle clamp. You can then swing

the additional handle (8) into the most comfortable working

position for you. Now turn the additional handle in the op-

posite direction again until the additional handle is secure.

Tiefenanschlag (Fig. 3 – Item.9)

The depth stop (9) is held in place with the locking

screw (A) on the additional handle (8) by means of a

clamp.

• Undo the locking screw (A) and t the depth stop (9).

• Set the depth stop (9) to the same level as the drill bit.

• Pull the depth stop (9) back by the required drilling

depth.

• Retighten the locking screw (A).

• Now drill the hole until the depth stop (9) touches the

workpiece.

Tool insertion (Fig. 4)

• Clean the tool before insertion and apply a thin coa-

ting of drill bit grease to the shaft of the tool.

• Pull back and hold the locking sleeve (2).

• Insert the dust-free tool into the tool mounting as far

as it will go whilst turning it. The tool will lock itself.

• Check that it is properly secure by pulling the tool.

Tool removal (Fig. 5)

Pull back and hold the locking sleeve (2) and remove

the tool.

Dust collection device (Fig. 6)

Slide the dust collection device (B) over the drill bit

before carrying out any hammer drilling vertically above

your head.

Operation

Danger

To prevent all danger, the machine must only be

held using the two handles (5/8). Otherwise there may

be a risk of suff ering an electric shock if you drill into

cables.

Status indicator (Fig.1)

The status indicator (6) lights up when the power plug is

connected.

Switching On and Off (Fig.1)

To switch on: Press and hold the operating switch (4).

To switch off : Let go of the operating switch (4)

Button hammer drilling / chiselling (Fig. 7)

• For hammer drilling, press the button (D) on the rotary

switch (3) and simultaneously turn the rotary switch

(3) to position E.

• For chiseling, press the button (D) on the rotary switch

(3) and simultaneously turn the rotary switch (3) to

position F. In switch position F the chisel is not locked.

• For chiseling, press the button (D) on the rotary switch

(3) and simultaneously turn the rotary switch (3) to

position G. The chisel is locked in position G.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zgonc YPL 1250 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info