Bedienungsanleitung Zibro D 2010 (Seite 5 von 8) (Englisch)

460186

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

FUNCTIONS

The appliance can run in either “Stand-Alone Mode”, where all humidity is removed from the surrounding air

and collected in the built-in water tank in the appliance, or “Continuous Draining Mode”, where the water is

removed from the air and led to an external drain via the built-in outflow using the attached plastic hose.

AND-ALONE MODE

Here, the rubber plug is placed in the outlet pipe on the back of the appliance, and all humidity is removed from

the air and collected in the built-in water tank. When the tank is full, the light on the control panel comes on ,

the appliance switches off and also emits a short beep to show that the water tank is full. Once this happens, the

water tank must be removed and emptied. When the empty tank is replaced, the dehumidifier starts again auto-

matically.

CONTINUOUS DRAINING MODE

Here, the rubber plug is removed from the outflow pipe on the back of the appliance and one end of the

accompanying transparent, flexible plastic pipe is pushed over the outflow pipe. (The rubber plug can be pushed

over the protruding tap above the outflow pipe to avoid it getting lost). The other end of the plastic pipe is led

downwards to a place where the humidity can drain away continuously

. As a result, water does not collect in the

built-in tank, and the visual and acoustic signals indicating that the built-in water tank is full do not function.

The appliance runs continuously when used in this manner.

FULL WATER TANK

Using the “Stand-Alone” function, humidity is removed from the air and collected in the built-in water tank.

When the tank is full, the light on the control panel comes on, the appliance switches of

f and also emits a short

beep to show that the water tank is full. When this happens, the water tank must be removed and emptied.

Once the empty tank is replaced, the dehumidifier starts again automatically. The tank should be placed back in

place for the appliance to run.

DIGITAL DISPLAY

1. Connect the appliance to the power supply. Switch on using the “ON/OFF” button (2-3 seconds). The equip-

ment starts in LOW position (energy saving). The current room temperature and air humidity are shown in

the electronic display. This is also the setting for continued dehumidification.

Then:

2. Press “ON/OFF” once: The appliance shuts down when the relative humidity is lower than 40%

Press “ON/OFF” twice: The appliance shuts down when the relative humidity is lower than 50%

4. Press “ON/OFF” three times: The appliance shuts down when the relative humidity is lower than 60%

5. Press “ON/OFF” four times: The appliance shuts down when the relative humidity is lower than 70%

6. Press “ON/OFF” five times: HIGH speed (maximum) dehumidification level is activated. The current room tempera-

ture and air humidity are shown in the electronic display. This is also the setting for continuous dehumidification.

7. Press “ON/OFF” six times: The appliance shuts down when the relative humidity is lower than 40%

8. Press “ON/OFF” seven times: The appliance shuts down when the relative humidity is lower than 50%

9. Press “ON/OFF” eight times: The appliance shuts down when the relative humidity is lower than 60%

10. Press “ON/OFF” nine times: The appliance shuts down when the relative humidity is lower than 70%

11. Press “ON/OFF” ten times: the dehumidifier returns to the start setting, which is the lowest setting for

dehumidification (energy saving function). Then repeat the process above.

The display shows:

A the temperature in the room

B the relative humidity

C and the relative humidity by which the appliance will stop dehumidifying

4. CLEANING AND MAINTENANCE

CLEANING THE AIR FILTER

1. The air filter must be cleaned regularly. The frequency of cleaning depends on the amount of dust, but

under normal circumstances it is suggested that cleaning be undertaken after 100 hours of operation and

more often in very dusty conditions.

2. Switch off the appliance and remove the cord from the socket.

3. Access to the air filter is gained by removing the cover to the air intake on the side of the appliance. This is

done by removing the cover horizontally from the appliance.

4. The air filter can now be removed by pressing down the 2 pins on top of the filter and twisting the filter

top off before the filter is removed.

man_D2010 ('09).qxd 02-10-2009 14:42 Pagina 29

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro D 2010 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zibro D 2010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info