Bedienungsanleitung Zibro DONATA 161 IDRO (Seite 3 von 62) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

564202

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Starting the Stove

Press button for a couple of seconds until the pellet boiler

stove starts.

Pellet Boiler stove start up

CAUTION!

The brazier should be cleaned before each starting.

Before switching on the pellet stove, make sure that the pel-

let hopper is full, the combustion chamber is clean, the glass

door is closed, the power supply plug is connected and the

switch on the back is set to “1.”

The LED is on when the parameter

UT01 on the menu is not on OFF and

the weekly or daily programming are

set.

CAUTION!

It is advisable to use dry wood pellets, up to 6 mm in

diameter.

“Fan” will be displayed on the up-

per display and “ACC” on the lower

one. During this phase the unit

will carry out a diagnosis (around

20 seconds) on the fume extrac-

tion system.

“LOAD WOOD” is the next phase,

which indicates pellets should

be fed. The glow plug will heat

up to light the ﬁre.

When the fume temperature is

50º C (approx. 10 minutes), the

pellet boiler stove will conﬁrm

the ignition: “FirE” will be shown

on the upper display and “ON” on

the lower one.

After this phase, which lasts

around 5 minutes, the heating

power (e.g. po 6) and the room

temperature (e.g. 25°), will be si-

multaneously shown on the upper

display, and the system delivery

water temperature will be shown

on the lower display.

If the ﬂame does not start up correctly within 10 minutes, the

pellet boiler stove jams: you will read the words “ALAR” on the

upper display and the words “NO ACC” blinking on the lower di-

splay. Wait 10 minutes until the cooling phase is completed,

open the door, empty the brazier and start a new light-up.

Pict. 2

Preliminary checks

“SET”

LED SYMBOL

DESCRIPTION

The LED starts up every time the stove

is loading pellets

The LED blinks when the board signa-

lises a change in temperature or power

set by the infrared remote control.

The LED is on when the room tempera-

ture reaches the value set on the menu

SET Water.

The LED blinks to indicate that you are

entering the menu user/technician or

that you are modifying the temperature

set.

The LED switches on when the water

circulator is working.

Control Panel (Pict. 2)

Buttons and are used to adjust temperature, for

displays and for the programming functions.

Buttons and are used to adjust heating power.

Button is used to adjust temperature and programming

functions.

The upper and lower displays are used to view different

messages.

How to load pellets in the tank

You can load pellets in the tank through the door on the up-

per part of the stove.

Join the following procedure to load pellets:

• Open the door on the upper part of the stove;

• Load the wished pellets quantity with caution (load enough

pellets to grant a sufcient functioning of the stove);

• Close the door.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro DONATA 161 IDRO Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info