Bedienungsanleitung Zibro Kamin HYBRID E (Seite 7 von 16) (Englisch)

460316

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

F: The required tempe-

rature on the left, the

measured temperature

on the right.

E: When the 4-digit stops

blinking, the setting has

been locked to the indi-

cated value.

Check whether the fuel cap is straight and tightened properly. Reinstall the

removable tank in the heater (cap down). Close the lid.

C SETTING THE CLOCK

It is only possible to set the correct time, when the heater is connected to the

mains and not burning. Use the adjustment keys O to set the time. First press

either of the two keys to switch on the function (the 4-digit K will start blinking).

Next, set the hours using the key on the left (Nhour) and the minutes using the

key on the right (Mmin.). Press once to increase the value by one step. When you

hold down the key, the value will continue going up, until you release the key

again. After approximately 10 seconds the 4-digit will stop blinking and the set-

ting will be locked. 5 minutes after switching off the heater, the information on

the display will disappear and the heater will automatically switch into the stand-

by position.

When the heater has been unplugged (or after a power failure), the time needs

to be set again.

D IGNITING THE HEATER

When used for the first time, a new heater may give out a smell for a short while.

You should therefore provide extra ventilation.

Always ignite the heater with the

button L

. Never use matches or a cigarette

lighter.

Just press the button L to ignite the heater. The POWER lamp will start blinking,

indicating that the ignition procedure has started. This will take a short while. In

the meantime the electric heating has already started 3 seconds after pressing the

button L.

Once the heater is burning, the POWER lamp will remain lit (blue). The information

display K will show two numbers. The light next to them indicates that these

numbers refer to the temperatures (Fig. F). The actual room temperature is

indicated below ROOM, while the temperature setting is indicated below SET. The

latter can be changed with the adjustment keys (refer to Section E).

Prior to igniting the heater, always check for sufficient fuel in the removable tank.

Igniting the electrical heater

Press the

button to ignite the electrical heater. The electric heating lamp will

light up (red). Electric heating will start 3 seconds after pressing the

button.

The electric heating will stop automatically when the room temperature reaches

the set temperature. The electric heating will restart automatically when the room

temperature drops. By pressing the electric heating button

, the electric heating

lamp will go out and electric heating will stop. The electric heating can be turned

off manually. By pressing the electric heating button again, electric heating will

start.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro Kamin HYBRID E Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zibro Kamin HYBRID E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info