Bedienungsanleitung Zibro Kamin Laser (Seite 28 von 34) (Englisch, Holländisch, Dänisch, Französisch, Italienisch)

460437

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

CODE INFORMATION WHAT TO DO

e - 0 Temperature within the heater too high. Cool-down and re-ignite.

f - 0 Power interrupted. Re-ignite the heater.

e - 1 Faulty thermostat. Contact your dealer.

f - 1 Faulty burner thermistor. Contact your dealer.

e - 2 Starting problems. Contact your dealer.

e - 5 Tipping-over protection. Re-ignite the heater.

e - 6 Poor burning. Contact your dealer.

e - 7 Room temperature If necessary,

above 28°C. re-ignite the heater.

e - 8 Defective booster. Contact your dealer.

e - 9 Air filter dirty; or Clean filter

Fuel pump dirty. Contact your dealer.

-- : -- Out of fuel. Refill removable tank.

(& blinking

FUEL-light)

-- : -- Too little ventilation. Ventilate better.

(& blinking

VENT-light)

Always contact your Zibro Kamin dealer for any malfunctioning not listed above.

I CHILDPROOF LOCK

The childproof lock can be used to prevent children accidentally changing the

heater settings. When the heater is burning and the childproof lock is on, the

heater can only be switched off. Other functions are blocked then. If the heater

has already been switched off, the childproof lock also prevents accidental

ignition of the heater.

Activate the childproof lock by pressing the appropriate key ƺ and holding it down

for more than 3 seconds. The KEY-LOCK indicator light will light up (Fig. I),

indicating that the childproof lock has been activated. Switch off the childproof lock

by pressing the key

ƺ and holding it down for more than 3 seconds once again.

J THE CORRECT USE OF 'SAVE'

The 'SAVE' function allows you to limit the temperature. When this function is

activated, the heater will automatically switch off, when the room temperature

exceeds the set temperature by 4°C. Subsequently, when the room temperature has

dropped again to the set temperature, the heater will automatically switch on again.

Activate the 'SAVE' setting by pressing the appropriate ƽ key. The SAVE indicator

light will light up (Fig. J). Switch off the function by pressing the SAVE key once

again.

Without the 'SAVE' setting your heater will maintain the set temperature by

approximation as well, by adjusting its heating capacity. 'SAVE' is an economy

setting, which you can use when, for instance, you are not present in the room

or to keep it frost-free.

e-: 0

SET ROOM

In case of any

malfunctioning the

information display will

tell you what is the

matter.

VE KEY-LOCK POWER

I: When the KEY-LOCK

light lights up, the

childproof lock has been

activated.

TEMP

CLOCK

TIMER

HOUR MIN

J: When the SAVE light

lights up, the heater will

automatically switch on

or off in order to remain

within a specified

temperature range.

☞

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro Kamin Laser Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zibro Kamin Laser

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info