Bedienungsanleitung Zibro Kamin SRE227E (Seite 8 von 15) (Englisch)

564078

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

F: The required tempe-

rature on the left, the

measured temperature

on the right.

E: When the 4-digit stops

blinking, the setting has

been locked to the indi-

cated value.

Check whether the fuel cap is straight and tightened properly. Reinstall the

removable tank in the heater (cap down). Close the lid.

C SETTING THE CLOCK

It is only possible to set the correct time, when the heater is connected to the

mains and not burning. Use the adjustment keys ƹ to set the time. First press

either of the two keys to switch on the function (the 4-digit ¸ will start blinking).

Next, set the hours using the key on the left (Ĭhour) and the minutes using the

key on the right (įmin.). Press once to increase the value by one step. When you

hold down the key, the value will continue going up, until you release the key

again. After approximately 10 seconds the 4-digit will stop blinking and the set-

ting will be locked. 5 minutes after switching off the heater, the information on

the display will disappear and the heater will automatically switch into the stand-

by position.

When the heater has been unplugged (or after a power failure), the time needs

to be set again.

D IGNITING THE HEATER

When used for the first time, a new heater may give out a smell for a short while.

You should therefore provide extra ventilation.

Always ignite the heater with the

button ¹

. Never use matches or a cigarette

lighter.

Just press the button ¹ to ignite the heater. The POWER lamp will start blinking,

indicating that the ignition procedure has started. This will take a short while. Once

the heater is burning, the POWER lamp will remain lit (red). The information display

¸ will show two numbers. The light next to them indicates that these numbers

refer to the temperatures (Fig. F). The actual room temperature is indicated below

ROOM, while the temperature setting is indicated below SET. The latter can be

changed with the adjustment keys (refer to Section E).

Prior to igniting the heater, always check for sufficient fuel in the removable tank.

E SETTING THE REQUIRED TEMPERATURE

The temperature setting can only be adjusted, when the heater is burning. Use

the adjustment keys ƹ to adjust the temperature. First press either of the two

keys to switch on the function (the °C mark ¸ will start blinking). Next, adjust the

temperature using the key on the right (įmin.) to set the temperature to a higher

setting and the key on the left (Ĭhour) to lower the temperature. Press once to

increase the value one step. After approximately 10 seconds the °C mark will stop

blinking and the setting will be locked (Fig. F).

The available temperature settings range from 6°C minimum to 28°C maximum.

When the heater has been unplugged (or after a power failure), the temperature

will reset to the factory setting of 20°C.

p052_061_SRE227E_uk.indd 56 19-06-12 15:48

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro Kamin SRE227E Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zibro Kamin SRE227E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info