Bedienungsanleitung Zibro Kamin SRE237E (Seite 9 von 14) (Englisch)

460314

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

H THE INFORMATION DISPLAY

The information display ¹ not only serves as an indicator of the (set) time and

temperature (Sections C, E, and F), it also indicates any malfunctioning of the

heater. The code on the information display tells you what is the matter:

CODE INFORMATION WHAT TO DO

e - 0 Temperature within the heater too high. Cool-down and re-ignite.

f - 0 Power interrupted. Re-ignite the heater.

e - 1 Faulty thermostat. Contact your dealer.

f - 1 Faulty burner thermistor. Contact your dealer.

e - 2 Starting problems. Contact your dealer.

e - 5 Tipping-over protection. Re-ignite the heater.

e - 6 Poor burning. Contact your dealer.

e - 7 Room temperature If necessary,

above 32°C. re-ignite the heater.

e - 8 Defective booster. Contact your dealer.

e - 9 Air filter dirty; or Clean filter

Fuel pump dirty. Contact your dealer.

The heater has been in operation

continuously for a period of 69 hours

and has turned itself off automatically. Switch the heater back on.

-- : --

Out of fuel. Refill removable tank.

-- : --

Too little ventilation. Ventilate better.

e - 1 1

Too little ventilation. Ventilate better.

Always contact your dealer for any malfunctioning not listed above and/or when

the error keeps occurring after taking the corrective measure as described above.

AUTOMATIC DEACTIVATION

This heater is fitted with a safety system that ensures that it switches off

automatically after 69 hours continuous operation. The following will then appear

in the display: . If desired, you can switch the heater on again by pressing

the button Ƹ (see Section D).

AUTOMATIC CLEANING MODE

When the heater has been burning continuously for two hours at its highest

setting, the burner will automatically start an autoclean procedure. The display

will show the autocleaning code cl:05 running back to cl:01. The procedure takes 5

minutes, during which the heater will burn at its lowest setting, while the burner

autocleans. When the burner is clean again, the heater will automatically switch

back to the highest setting again.

I CHILDPROOF LOCK

The childproof lock can be used to prevent children accidentally changing the

heater settings. When the heater is burning and the childproof lock is on, the heater

can only be switched off. Other functions are blocked then. If the heater has already

been switched off, the childproof lock also prevents accidental ignition of the

heater.

Activate the childproof lock by pressing the appropriate key ƹ and holding it

down for more than 3 seconds. The KEY-LOCK indicator

( )

will appear on the

information display (Fig. I), indicating that the childproof lock has been activated.

Switch off the childproof lock by pressing the key ƹ and holding it down for more

than 3 seconds once again.

I: When the mark

appears, the childproof

lock has been activated.

In case of any

malfunctioning the

information display will

tell you what is the

matter.

man_SRE237E_uk.qxd:uk 24-05-11 15:56 Page 58

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro Kamin SRE237E Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zibro Kamin SRE237E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info