Bedienungsanleitung Zibro Laser FF 95 (Seite 38 von 71) (Englisch, Holländisch, Französisch)

481445

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

Chapter 1, INSTALLATION

☞

CHECKLIST

• Check whether the heater has been connected to a

suitable socket.

• Check that a suitable quantity of petroleum is in the

fuel tank.

• Ensure that the fuel is free of water or other

contaminants.

• Check that the fuel tank is in good working order –

it must be free of rust, corrosion and/or leaks.

• Inspect the fuel pipe for signs of leaks, loose

connections, cracks, air bubbles or blockages.

• Check that the fuel valves on the fuel tank and the

fire safety valve are open in order to allow the free

flow of fuel.

• Check outside the building in order to ascertain that

there is no fuel or obstructions to the free

circulation of air in the area immediately adjacent

to the exhaust pipe.

• Inspect the inlet air hose for cracks, loose

connections or blockages.

• Check the outlet air hose for cracks, loose

connections or blockages.

• Check the back of the heater to ensure that the

airflow to the air circulation ventilator is not

obstructed.

• Inspect the interior of the building to ensure that

the area immediately adjacent to the heater is free

of fuel and objects that may obstruct the free flow

of air.

• Check that the room sensor is not exposed to

draughts, direct sunlight or heat radiated directly

from the heater.

• Use a spirit level to check that the heater is level.

If this inspection brings any faults to light, resolve these

problems before using the heater.

Use only water-free high quality pure

paraffin oil. Never use gasoline, LPG,

camping gas or other flammable liquids.

The use of these substances may cause

explosions or fire.

Available fuel supply options

The fuel supply of the Laser 95 can be set up as follows:

Large gravity-operated exterior tank

To install a large gravity-operated exterior tank, follow

the instructions below. We recommend that you call in

a recognised installer.

The inlet pressure to the heater may not exceed 2.5 psi.

Use a pressure reduction valve with a maximum thrust

of 2.5 psi ( ± 0.17 bar).

The installation height of the bottom of the fuel tank

must be 40 cm or more above the level of the floor on

which the heater is standing. This will ensure that there

is sufficient fuel inlet pressure. The distance between

the floor surface on which the heater is standing and

the top of the fuel tank may not exceed 2.5 metres.

This will prevent excessive fuel inlet pressures.

The pipe may not have any inverted U-bends (to pre-

vent air pockets that may block the fuel supply).

We recommend using a water-blocking filter in the fuel

pipe leading into the tank. A cut-off valve must be fit-

ted to the tank.

We recommend installing a fire safety valve and a fuel

filter in the fuel pipe.

The use of a cut-off valve, placed just before the pipe

enters the building, will limit the quantity of fuel to be

tapped off to a minimum if the heater requires mainte-

nance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro Laser FF 95 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zibro Laser FF 95

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info