Bedienungsanleitung Zibro LC-DX320 Toyotomi (Seite 18 von 146) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch)

650595

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

G: The required tempe-

rature on the left, the

measured temperature

on the right.

F: When the 4-digit

stops blinking, the set-

ting has been locked to

the indicated value.

B FILLING FUEL

ill the removable tank in a suitable place since there can alays be some

spillage. ollo the procedure belo:

Make sure that the heater is switched off.

Open the upper lid and lift the removable tank out of the heater (ig. B).

Put don the removable tank (cap pointing upards, handle on floor) and

scre off the fuel cap (ig. C).

NOTE: Some drops may leak from the tank.

ill the removable tank using a fuel pump (refer to fuel pump operation

instructions.) Make sure that it is in a higher position than the removable tank

(ig. D). Insert the ribbed hose into the opening of the removable tank.

Check the removable tank fuel gauge hile filling the tank (ig. E). Stop

filling once the gauge indicates that the tank is full. Never overfill the tank,

especially not when the fuel is very cold (fuel expands when it heats up).

Let the remaining fuel in the pump flow back into the jerrycan and carefully

remove the pump. Carefully screw the fuel cap back on the tank. Clean off

any spilled fuel.

Check whether the fuel cap is straight and tightened properly. Reinstall the

removable tank in the heater (cap down). Close the lid.

C SETTING THE CLOCK

It is only possible to set the correct time, when the heater is connected to the

mains and not burning. Use the adjustment keys  to set the time. irst press

either of the to keys to sitch on the function (the -digit  will start blinking).

Next, set the hours using the key on the left (hour) and the minutes using the

key on the right (min.). Press once to increase the value by one step. When you

hold down the key, the value will continue going up, until you release the key

again. After approimately 10 seconds the -digit ill stop blinking and the set-

ting ill be locked (ig. ). 5 minutes after sitching off the heater, the informa-

tion on the display will disappear and the heater will automatically switch into the

stand-by position.

When the heater has been unplugged (or after a power failure), the time needs

to be set again.

D IGNITING THE HEATER

When used for the first time, a new heater may give out a smell for a short while.

You should therefore provide extra ventilation.

Alays ignite the heater ith the

button 

. Never use matches or a

cigarette lighter.

Just press the button  to ignite the heater. The POWER lamp ill start blinking,

indicating that the ignition procedure has started. This will take a short while.

Once the heater is burning, the POWER lamp ill remain lit (red). The information

display  will show two numbers. The light next to them indicates that these

numbers refer to the temperatures (ig. ). The actual room temperature is

indicated belo ROOM, hile the temperature setting is indicated belo SET. The

latter can be changed with the adjustment keys (refer to Section E).

Prior to igniting the heater, alays check for sufficient fuel in the removable tank.

E SETTING THE REQUIRED TEMPERATURE

The temperature setting can only be adjusted, hen the heater is burning. Use

the adjustment keys  to adjust the temperature. irst press either of the to

keys to switch on the function (the °C mark  will start blinking). Next, adjust the

temperature using the key on the right (min.) to set the temperature to a higher

setting and the key on the left ( hour) to loer the temperature. Press once to

increase the value one step. After approimately 10 seconds the C mark ill stop

blinking and the setting ill be locked (ig. ).

The available temperature settings range from C minimum to 28C maimum.

When the heater has been unplugged (or after a power failure), the temperature

will reset to the factory setting of 20°C.

empty

full

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro LC-DX320 Toyotomi Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zibro LC-DX320 Toyotomi

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info