Bedienungsanleitung Zibro Norma (Seite 54 von 114) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

460446

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

F. TECHNICAL SERVICE, ORIGINAL SPARE PARTS

Before leaving the factory, each stove has been carefully tested and commissioned.

Any repairs or commissioning that may become necessary during or after installa-

tion must be carried out by heating engineers authorized by Zibro. Original factory

spare parts can be obtained only and exclusively from our Technical Servicing Cen-

ters and authorized points of sale.

When contacting your dealer, the Technical Service Centre or the authorized hea-

ting engineer, ﬁrst make sure to be able to specify the model and serial number at

their ﬁrst request.

Only use by Zibro agreed spare parts. Using non Zibro spare parts will lead to nul-

liﬁcation of the warranty.

G. TROUBLE SHOOTING

Problem Possible cause Possible solution

Problems during start-up

Wood size is too big Use very dry small wood sticks be-

fore larger size wood

Wood is too humid Use seasoned (dry enough) wood

Not enough draught in the chim-

ney

Turn all settings to maximum ope-

ning and check that the chimney

ﬂue is not obstructed.

Check if chimney shut off damper

is fully opened

There is not enough fresh air sup-

plied to the room

Immediately provide an aeration

grid, please refer to an authorized,

specialised heating engineer.

Too much draught Primary air inlet to minimum

Condensation forms

Chimney ﬂue section is too large Reduce the chimney ﬂue section

using thermally insulated pipes

(needs to be done by specialised

heating engineer, such as for

example a chimney sweeper or

chimney installer)

Chimney ﬂue is not insulated well Line the chimney ﬂue with insula-

ting material (only by authorized

professional)

Combustion is too slow Open air parameters to increase ﬁre

and temperature of outlet fumes

Smoke leaks out of the stove

Chimney ﬂue is not insulated well Line the chimney ﬂue with insula-

ting material (only by authorized

professional)

Unfavourable weather conditions

(too strong wind)

Chimney pot is not wind protected,

(re-)place it.

Unfavourable weather conditi-

ons, (too little wind, misty/foggy

weather conditions)

This is normal, operating the stove

at these weather conditions should

be avoided.

Wood is too humid Use seasoned, dried wood

Charging door seal is damaged or

worn out

Have charging door seal replaced

by authorized technician

Glass gets too dirty

Not enough draught in the chim-

ney

Turn all settings to maximum ope-

ning and check that the chimney

ﬂue is not obstructed (needs to be

done by specialised heating engi-

neer, such as for example a chim-

ney sweeper)

Wood is too humid Use seasoned, dried wood

Combustion is too slow Open air parameters to increase ﬁre

and temperature of outlet fumes

Fuel is of poor quality Use fuel as described in paragraph

D.3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro Norma Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zibro Norma

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info