Bedienungsanleitung Zibro SRE 235 E (Seite 9 von 14) (Englisch)

460397

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

The heater has been in operation

continuously for a period of 69 hours

and has turned itself off automatically. Switch the heater back on.

-- : --

Out of fuel. Refill removable tank.

-- : --

Too little ventilation. Ventilate better.

e - 1 1

Too little ventilation. Ventilate better.

Always contact your Zibro dealer for any malfunctioning not listed above.

AUTOMATIC DEACTIVATION

This heater is fitted with a safety system that ensures that it switches off

automatically after 69 hours continuous operation. The following will then appear

in the display: . If desired, you can switch the heater on again by pressing

the button Ƹ (see Section D).

AUTOMATIC CLEANING MODE

When the heater has been burning continuously for two hours at its highest

setting, the burner will automatically start an autoclean procedure. The display

will show the autocleaning code

cl:05 running back to cl:01. The procedure takes 5

minutes, during which the heater will burn at its lowest setting, while the burner

autocleans. When the burner is clean again, the heater will automatically switch

back to the highest setting again.

THE USE OF THE MOTION DETECTION SENSOR

This heater is equipped with a motion detection sensor. The sensor is placed at the

front side of the heater and it signals every single movement. The motion

detection sensor has a horizontal detection angle of 80

and a vertical detection

angle of 20

. The sensor detects movements as far as 7 m.

If the sensor does not detect movements for 10 minutes then the heater will

automatically switch to a lower combustion level. As a result less fuel will be used.

Switch on the motion detection sensor;

Switching on the motion detection sensor can only be done when the heater is

turned on. Push the “Motion” button . A signal will sound and the “Motion”

light will light up (green).

If the sensor does not detect movements for 10 minutes then the heater will

automatically switch to a lower combustion level. The motion detection sensor

light keeps lighted up. If the sensor detects movement the motion light will blink.

The heater switches back to the latest temperature setting.

Switch off the motion detection sensor;

The Motion detection sensor can be switched off by pressing the “Motion” button

again. A sound signal will be heard and the “Motion” light will go out.

I CHILDPROOF LOCK

The childproof lock can be used to prevent children accidentally changing the

heater settings. When the heater is burning and the childproof lock is on, the heater

can only be switched off. Other functions are blocked then. If the heater has already

been switched off, the childproof lock also prevents accidental ignition of the

heater.

Activate the childproof lock by pressing the appropriate key ƹ and holding it

down for more than 3 seconds. The KEY-LOCK indicator

()

will appear on the

information display (Fig. I), indicating that the childproof lock has been activated.

Switch off the childproof lock by pressing the key

ƹ and holding it down for more

than 3 seconds once again.

I: When the mark

appears, the childproof

lock has been activated.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro SRE 235 E Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zibro SRE 235 E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info