Bedienungsanleitung Zibro SRE835E (Seite 8 von 15) (Englisch)

564104

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

F: When the 4-digit stops

blinking, the setting has

been locked to the indi-

cated value.

empty full

B FILLING FUEL

Fill the removable tank in a suitable place since there can always be some spillage.

Follow the procedure below:

Make sure that the heater is switched off.

Open the upper lid and lift the removable tank out of the heater (Fig. B).

Note: Some drops may leak from the tank. Put down the removable tank (cap

pointing upwards, handle on floor (Fig. C) and screw off the fuel cap.

Fill the removable tank using a fuel pump (refer to fuel pump operation

instructions.) Make sure that it is in a higher position than the removable tank

(Fig. D). Insert the ribbed hose into the opening of the removable tank.

Check the removable tank fuel gauge while filling the tank (Fig. E). Stop fill-

ing once the gauge indicates that the tank is full. Never overfill the tank,

especially not when the fuel is very cold (fuel expands when it heats up).

Let the remaining fuel in the pump flow back into the jerry can and carefully

remove the pump. Carefully screw the fuel cap back on the tank. Clean off

any spilled fuel.

Check whether the fuel cap is straight and tightened properly. Reinstall the

removable tank in the heater (cap down). Close the lid.

C SETTING THE CLOCK

It is only possible to set the correct time, when the heater is connected to the

mains and not burning. Use the adjustment keys ƺ to set the time. First press

either of the two keys to switch on the function (the 4-digit ¹ will start blinking).

Next, set the hours using the key (Ĭhour) and the minutes using the key (įmin.).

Press once to increase the value by one step. When you hold down the key, the

value will continue going up, until you release the key again. After approximately

10 seconds the 4-digit will stop blinking and the setting will be locked. 5 minutes

after switching off the heater, the information on the display will disappear and

the heater will automatically switch into the stand-by position.

When the heater has been unplugged for more than 10 minutes (or after a

power failure), the time needs to be set again.

D IGNITING THE HEATER

When used for the first time, a new heater may give out a smell for a short while.

You should therefore provide extra ventilation.

Always ignite the heater with the

button

. Never use matches or a cigarette

lighter.

Just press the button Ƹ to ignite the heater.

The

button will start blinking, indicating that the ignition procedure has start-

ed. This will take a short while. Once the heater is burning, the

button Ƹ will

remain lit (red). The information display ¹ will show two numbers (Fig. G). The

actual room temperature is indicated below ROOM, while the temperature setting

is indicated below SET. The latter can be changed with the adjustment keys (refer

to Section E).

Prior to igniting the heater, always check for sufficient fuel in the removable tank.

p052_061_SRE835E_uk.indd 56 28-06-12 11:22

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro SRE835E Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zibro SRE835E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info