Bedienungsanleitung Zonder merk T861 (Seite 2 von 2) (Englisch)

121310

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

displayed just to the right of the seconds count

Set current Date and Time

1. Press and hold the 'SET' button until the day (MO) starts flashing

2. Use the

'<-'

and

'->'

buttons to select the current day.

3. Press the 'SET' button the hours flash

4. Use the '<-' and '->' buttons to select the current hour.

5. Press the 'SET' button the minutes flash

6. Use the

'<-'

and '->' buttons to select the current minute.

7. Wait 5 seconds and the timer will drop out of time set mode back to normal mode.

Set Programmes

The unit has 20 separate timers each with separate On and Off times, each of

which can be set to act on a variety of different days of the week, e.g. every day

MO TU WE TH FR SA SU is selected or just weekends SA SU is selected, or a

single day e.g. only Wednesdays, WE is selected.

To set timers

1. Press the

'<-'

'->'

button

2. 1

flashes, this indicates you are going to set the ON time of timer one, if

you want to set a different timer press the

'<-'

'->'

button to cycle

through the 20 ON and OFF timers.

3. Press 'SET' the days selection flashes

4. Use the '<-' and

'->'

buttons to select the days you wish this timer to operate on

5. Press 'SET' the hours f1ashe

6. Use the '<-' and '->' buttons to select the hour at which you wish this timer to operate

7. Press 'SET' the minutes flash

8. Use the

'<-'

and

'->'

buttons to select the minutes at which you wish this timer to operate

9. Press 'SET' the current timer, e.g. 1

flashes

10. Use the '<-' and '->' buttons to select the next timer to set e.g. set 1

0FF

11. Repeat Steps 3 to 11 above

When done setting the timers wait 5" and the unit will go back to normal operating mode.

Operation

Once programmed the timer can be set using the triangular button with the picture of a finger,

there are three basic modes

1. OFF: always off

2. ON: always on

3. AUTO switches off and on based on the set timers.

When AUTO OFF is shown the timer socket is currently off, when AUTO ON is

shown the timer socket is currently on

Random Delay Start Mode (RND)

Random Delay Start mode delays the programmed start and finish times by between 2 and 32 minutes,

this can be used to give the impression that a timer is not being used to turn lights on and off.

Press the RND button to enable or disable random mode.

2. If random mode is set "RND" appears on the right hand side ofthe display, blank in normal mode.

Countdown Timer Mode (CTO)

Countdown Timer Mode allows the timer to switch on after a pre-determined time delay, to

set CTD mode:

1. In normal mode, press

'<-'

to enter CTD mode

2. Press 'SET' and the

'<-'

an~ '->' keys to preset the countdown time (in the same way

as for the timer modes above)

3. Once back at the f1ashing ON display, press 'CTD' to start the countdown, 'CTD' is displayed

above the seconds countdown

To pause and restart the countdown, press 'CTD' button

Red Indicator Lamp

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zonder merk T861 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info