Bedienungsanleitung Zoofari ZTSD 36 B1 - IAN 315533 (Seite 17 von 60) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

773322

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

■ 14 │ GB│IE ZTSD 36 B1

Operation

The fur to be cut must be dry and clean. Brush the

fur through to remove any knots.

1) Remove the blade guard 7 from the cutting

head 1.

2) Place the required trimming guide (1 – 6) with

the prongs facing upwards on the cutting head 1

and thereby press the ﬂap of the trimming guide

(1 – 6) down ﬁrmly onto the lower metal edge

of the cutting head 1 (see illustration).

■ Ensure that the trimming guide (1 – 6) has

properly engaged and is secured before starting

to cut/trim the fur.

NOTE

► It is advisable to ﬁrst trim a small area so as to

test the individual comb attachments (1 – 6).

Start with a comb attachment for long hair

(1/2“ 4 or 3/8“ 3) and, if necessary, use a

shorter one. The comb attachments (1 – 6)

permit cutting lengths from 3 to 13 mm.

3) Switch the appliance on by sliding the On/Oﬀ

switch 3 to the position “ON“.

4) Slowly run the appliance through the fur against

the direction of hair growth. Hold the appliance

so that the trimming guide (1 – 6) is as ﬂat as

possible against the animal.

– In addition, with the adjustment switch 4 the

cutting length of the cutter head 1 can be

adjusted in steps(up to 2 mm) without having

to exchange the comb attachment (1 – 6).

To do this, slide the adjustment switch 4

backwards to increase the cutting length in

steps. With this the cutting length of the

respectively attached comb attachment is also

increased by up to 2mm.

Slide the adjustment switch 4 forward again

to reduce the cutting length or to bring the

comb attachment (1 – 6) back into its

original position.

– Through removal of the individual trimming

guide (1 – 6), i.e. using only the cutting

head 1 itself, you can cut clean contours.

5) After use, switch the appliance oﬀ by sliding the

On/Oﬀ switch 3 to the position “OFF“.

Cleaning and Care

DANGER! ELECTRIC SHOCK

► Before cleaning, remove the plug from the

mains power socket.

CAUTION! PROPERTY DAMAGE!

► NEVER submerse the appliance in water or

other liquids.

■ Take the respective trimming guide (1 – 6), if

ﬁtted, oﬀ.

■ Using exclusively the cleaning brush 8, remove

the hairs from the cutting head 1. Wipe oﬀ the

cutting head 1 with a damp cloth. After this,

dry the cutting head 1 oﬀ with a dry cloth.

We recommend that you occasionally clean the

cutting head 1 with medicinal alcohol.

■ If in regular use, the cutting head 1 should be

oiled occasionally. For this, use the supplied

blade oil 9.

■ Remove excess oil with a dry cloth.

■ Clean the housing with a soft, dry lint-free cloth.

In cases of stubborn soiling, clean the housing

using a damp cloth and then dry it oﬀ with a dry

cloth.

■ Clean the trimming guides (1 – 6) in warm

water. Add a little mild detergent. Dry all parts

well before re-use.

■ Store the appliance in a dry and dust free

location. When it is in storage, place the blade

guard 7 on the cutting head 1.

IB_315533_ZTSD36B1_LB8.indb 14 22.01.19 12:33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zoofari ZTSD 36 B1 - IAN 315533 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info