Bedienungsanleitung Zoom B2.1u (Seite 5 von 37) (Englisch)

629759

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

ZOOM B2.1u

Operating the B2.1u on batteries

Turn the B2.1u over and open the cover

of the battery compartment on the bottom.

B2.1u

bottom view

Latch

Cover

Press the latch to release

it and then raise the cover.

Insert four fresh IEC

R6 (size AA) batteries.

Close the cover of

the battery compartment.

Four IEC R6

(size AA) batteries

Insert batteries facing

in alternate directions.

Use four IEC R6 (size AA) batteries.

When the batteries are getting low, the

indication "bt" appears on the display.

Push the cover in until the

latch audibly snaps into

place.

LO EQZNR/MIXDRIVE/SYNTHCOMP/LIMIT WAH/EFX MOD/SFXHI EQ DELAY REVERB

IN OUT

Terms Used in This Manual

This section explains some important terms that are used throughout the B2.1u documentation.

■

Effect module

As shown in the illustration above, the B2.1u can be

thought of as a combination of several single effects.

Each of these effects is referred to as an effect module.

In addition to modules comprising compressor and

limiter effects (COMP/LIMIT), amp simulator/synth

bass effects (DRIVE/SYNTH), and modulation/special

effects (MOD/SFX), the B2.1u also provides a module

for ZNR (ZOOM Noise Reduction). Various

parameters such as effect intensity can be adjusted for

each module individually, and modules can be

switched on and off as desired.

■

Effect type

Within some effect modules, there are several

different effects which are referred to as effect types.

For example, the modulation/SFX effect module

(MOD/SFX) comprises chorus, flanger, pitch shifter,

delay, and other effect types. Only one of these can

be selected at a time.

■

Effect parameter

All effect modules have various parameters that can

be adjusted. These are called effect parameters.

In the B2.1u, effect parameters are adjusted with the

parameter knobs 1 – 3. Similar to the knobs on a

compact effect, these change aspects such as tonal

character and effect intensity. Which parameter is

assigned to each knob depends on the currently

selected effect module and effect type.

■

Patch

In the B2.1u, effect module combinations are stored

and called up in units referred to as patches. A patch

comprises information about the on/off status of each

effect module, about the effect type used in each

module, and about effect parameter settings. The

internal memory of the B2.1u holds up to 80 patches

(including 40 patches which allow read/write).

■

Bank and area

A group of ten patches is called a bank. The memory

of the B2.1u comprises a total of eight banks,

labelled A to d and 0 to 3. Banks A – d form the user

area which allows read/write. Banks 0 to 3 are the

preset area containing read-only patches.

The patches within each bank are numbered 0

through 9. To specify a patch of the B2.1u, you use

the format "A1" (patch number 1 from bank A), "06"

(patch number 6 from bank 0), etc.

■

Play mode/edit mode

The internal status of the B2.1u is referred to as the

operation mode. The two major modes are "play

mode" in which you can select patches and use them

for playing your instrument, and "edit mode" in

which you can modify the effects. The module

selector serves for switching between the play mode

and edit mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zoom B2.1u Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info