Bedienungsanleitung Zoom MRS-802 (Seite 24 von 184) (Englisch)

533782

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

Quick Tour

ZOOM MRS-802

Step 2: Recording the ﬁrst track

In this step, you record the ﬁrst track while listening to the

rhythm section. As an example we describe how to record an

electric guitar on track 1 with the insert effect.

2.1 Adjusting input sensitivity

Connect an instrument to the GUITAR/BASS jack

(

→

p. 15).

To connect a synthesizer or other component with line-level

stereo output, use the INPUT 1/INPUT 2 jacks on the rear

panel. To connect a guitar or bass, use the GUITAR/BASS

jack.

HINT

When something is connected to both the GUITAR/BASS

jack and the INPUT 1 jack on the rear panel,the GUITAR/

BASS jack has priority. To adjust the GUITAR/BASS input

sensitivity or switch the jack on/off, use the INPUT 1 control.

Press the [INPUT 1] key so that the key lights up.

The [INPUT 1]/[INPUT 2] keys serve to switch the

respective input on and off. While the key is lit, the input is

active.

HINT

To record the output of a synthesizer or similar in stereo,

connect the L and R output to the INPUT 1/INPUT 2 jacks

and press both the [INPUT 1] and [INPUT 2] keys so that both

keys are lit.

While playing the instrument, use the [INPUT]

control 1 to adjust sensitivity.

Adjust the control so that the [PEAK] indicator lights up

occasionally when you play the instrument at the loudest

level.

While playing the instrument, use the [REC LEVEL]

control to adjust the recording level.

The [REC LEVEL] control modiﬁes the signal level going

to the recorder (after passing the insert effect). The IN1/IN2

level meter in the lower left of the display shows the level.

Set the level as high as possible, but avoid settings that cause

the 0 dB indicator to light during play peaks.

If the recording level setting is too high, the [CLIP] indicator

of the [REC LEVEL] control lights up.

2.2 Applying the insert effect

The signal supplied to the MRS-802 can be modiﬁed with

the insert effect. This effect can be applied to the input, to

any track, or immediately before the [MASTER] fader. The

insert effect actually is a multi-effect unit that contains a

number of single effects (effect modules) such as

compressor, distortion, and delay, connected in series. A

combination of effect modules that can be used

simultaneously is called an “algorithm”.

The following steps show how to select an algorithm and

apply the insert effect to the guitar signal connected to the

GUITAR/BASS jack.

Press the [INPUT SOURCE] key in the effect

section.

The insert position of the insert effect is indicated on the 2nd

line of the display. The default is “IN” (INPUT). To change

the setting, turn the dial to select “IN”.

Lit

Lights up occasionally

INPUT 1 Level INPUT 2 Level

[CLIP] indicator

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zoom MRS-802 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zoom MRS-802

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info