Bedienungsanleitung Zoom MRS-802 (Seite 47 von 184) (Englisch)

533782

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

Reference [Track Editing]

ZOOM MRS-802

The subsequent steps will differ, depending on which

command was selected. See the sections for the respective

commands.

When the editing command has been executed,

repeatedly press the [EXIT] key to return to the

main screen.

HINT

After performing an edit function and rewriting the audio data

on a track, the original data cannot be restored. If you want

to retain the condition before editing, use the capture

function for that track (

→ p. 55).

Copying a speciﬁed range of data

You can copy the audio data of a speciﬁed range to a

speciﬁed position on a speciﬁed track. This action will

overwrite the existing data at the destination location. The

copy source data will be unchanged.

Refer to steps 1 - 6 of “Basic editing steps” to

select the copy source track/V-take, and press the

[ENTER] key.

The display changes as follows. This screen lets you specify

the copy range start point.

The edit range start point is shown on the left-hand counter

in hours, minutes, seconds, milliseconds, and on the right-

hand counter in measures, beats, and ticks.

Use the cursor left/right keys to move the ﬂashing

section of the counter, and turn the dial to specify

the copy start point.

The point can be speciﬁed in hours/minutes/seconds/

milliseconds. When a value is speciﬁed, the measure/beat/

tick counter reﬂects the new location.

If you move the ﬂashing section to the MARKER ﬁeld on

the display, you can specify a mark by turning the dial. In

this case, the mark position becomes the editing start point.

If you move to an area where no data are recorded, a “*”

symbol is shown.

Press the [ENTER] key.

The display changes to “Copy Src END”. This screen lets

you specify the copy range end point.

Use the same procedure as in step 2 to specify the

copy range end point.

If you press the PLAY [R] key at this point, the speciﬁed

range will be played.

Press the [ENTER] key.

The display now shows “Copy Dst TR xx-yy” (where xx is

the track number and yy the V-take number). This screen lets

you specify the copy destination track/V-take.

NOTE

• If you have selected a single track as copy source, only a

single track can be selected as copy destination.

• If you have selected two adjacent tracks or the master

track as copy source, only two adjacent tracks or the

master track can be selected as copy destination. In this

case, the currently selected V-take for each track becomes

the editing target.

Specify the copy destination track/V-take in the

same way as when selecting the copy source

track/V-take, and press the [ENTER] key.

The display changes as follows. This screen lets you specify

the start point on the copy destination V-take.

Copy source track

Copy

Copy destination track

Copy Src

START

0 0 0 0 001 1

Copy Src

END

0 213 0 058 3

Copy Dst

TR 1- 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zoom MRS-802 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zoom MRS-802

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info