Bedienungsanleitung Zoom MRS-802 (Seite 86 von 184) (Englisch)

533782

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

Reference [Rhythm]

ZOOM MRS-802

Inputting other event data

Once rhythm pattern information has been input to a rhythm

song, you can add various other information such as tempo

and rhythm section volume. Such data are called “event”

information.

In rhythm song mode ([SONG/PATTERN] key lit),

verify that the [DRUM] key is lit.

Press the REC [

] key.

Rhythm song step input becomes possible.

Press the cursor up key repeatedly to bring up the

indication “EV

→

” on the display.

This screen lets you check which event information is

entered at the current point. The symbol after “EV→” (such

as “Pt” or “TS”) denotes the type of event. Available events

and their symbols are listed in the table below.

HINT

• If no tempo information is input for the rhythm song, the

tempo currently set for the rhythm section will be used. To

ensure that a rhythm song will always play with the same

tempo, be sure to enter tempo information at the

beginning of the song.

• If desired, you can also adjust the tempo while a song is

playing by hitting the [TEMPO] key several times in

succession. Check the display to verify that the desired

tempo has been set.

Move to the location at which you want to input a

new event.

You can change the input location in the following three

ways.

(1) Moving in steps of a measure

Use the cursor left/right keys to move to the beginning of the

preceding or following measure.

(2) Specify the location in beats

Use the REW [T]/FF [Y] keys to move to the beginning of

the preceding or following beat.

(3) Specify the location in 16th note units

Repeatedly press the cursor up key to bring up the indication

“EV→”, and turn the dial to move forward or backward in

12-tick (16th note) units. You can check the position using

the counter display.

HINT

The current position is shown to the right of the counter in

measures / beats / ticks.

Use the cursor up/down keys to select the type of

event that you want to input.

If the event you select here has been input at the current

location, its value will be displayed. If there is no

corresponding event, the display will indicate “ ”. This

means that the previously input event will apply.

Turn the dial to input the value.

The event type “TimSig” can only be input in units of

measures. When you turn the dial within a measure, the

position automatically jumps to the start of the next

measure, and the new event is input at that location.

NOTE

When you change the TimSig event, only the measure and

beat division within the pattern changes. The duration of the

entire rhythm pattern does not change.

Input the other events in the same way.

Ptn

TimSig

Tempo

DrVOL

Type of

event

Content

Symbol

Range

Rhythm pattern

number

Time signature

Tempo

Drum track

volume

000 – 510

1 – 8(1/4 – 8/4)

40.0 – 250.0

0 – 15

TimSig

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zoom MRS-802 Seite 86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zoom MRS-802

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info