Bedienungsanleitung Zoom MRS-802 (Seite 142 von 184) (Englisch)

533782

142

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

Appendix

ZOOM MRS-802

142

Troubleshooting

If there are problems during operation of the MRS-802,

check the following points ﬁrst.

Problems during playback

■ No sound, or sound is very weak

• Check the connections to your audio system, and the

volume of your audio system.

• Make sure that the status keys in the mixer section are lit

in green and that the faders are raised. If a key is out, press

the it to make it light up in green.

• If a scene with the volume lowered has been assigned to a

mark, the volume will automatically be lowered when that

mark is reached. Delete the scene that is assigned to the

mark (→ p. 76).

• The recorder will not operate when the [DRUM] key is lit.

Press the [EXIT] key so that the [DRUM] key goes out.

■ Operating the fader does not affect the

volume

• On channels for which stereo link is turned on, the fader

of the even-numbered channel will have no effect. Either

turn stereo link off (→ p. 73), or operate the fader of the

odd-numbered channel.

■ The display indicates "Don't Play" and

playback is not possible

• The recorder will not operate in the current screen. Press

the [EXIT] key several times to switch to the main screen.

■ No sound from input signal, or sound is

very weak

• Make sure that the [INPUT 1]/[INPUT 2] key is lit.

• Make sure that the respective [INPUT] control is raised.

• Make sure that the [REC LEVEL] control is raised. If it is

raised, temporarily turn it down and then up again.

■ The indication "STOP RECORDER" is

shown on the display, and operation is

not possible.

The current operation is not possible while the recorder is

operating. Press the STOP [P] key to stop the recorder.

Problems during recording

■ Cannot record on a track

• Make sure that you have selected a recording track.

• Check whether you have run out of free space on the hard

disk (→ p. 125).

• Recording is not possible if the project is write-protected.

Either turn protect off (→ p. 127), or use a different

project.

■ The signal from an instrument or

microphone connected to the INPUT 1

jack is not input

• When something is connected to both the INPUT 1 jack

and the GUITAR/BASS jack, the GUITAR/BASS jack

has priority.

■ The recorded sound is distorted

• Check whether the input sensitivity setting ([INPUT

control) and recording level setting ([REC LEVEL]

control) are appropriate.

•Lower the fader so that the 0 (dB) dot of the level meter

does not light.

• If the EQ gain of the track mixer is set extremely high, the

sound may be audibly distorted even if the fader is

lowered. Set the EQ to an appropriate value.

Problems with effects

■ Insert effect does not apply

• Make sure that the [BYPASS/TUNER] key is out.

• Make sure that the insert effect is sent to the desired

location (→ p.101).

■ Send/return effect does not apply

• Make sure that the [CHORUS/DELAY] or [REVERB]

key is lit. If it is out, press the key several times to make it

light.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zoom MRS-802 Seite 142

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zoom MRS-802

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info