Bedienungsanleitung ZyXEL AMG1302-T series (Seite 80 von 320) (Englisch)

679704

Zoom out

Zoom in

Vorherige Seite

1/320

Nächste Seite

Chapter 6 Broadband

AMG1302/AMG1202-TSeries User’s Guide

The following table describes the labels in this screen.

Table 12 Network Setting > Broadband > Internet Connection: Advanced Setup

LABEL DESCRIPTION

RIP Direction RIP (Routing Information Protocol) allows a router to exchange routing information

with other routers. Use this field to control how much routing information the

AMG1302/AMG1202-TSeries sends and receives on the subnet.

Select the RIP direction from None, Both, In Only and Out Only.

RIP Version This field is not configurable if you select None in the RIP Direction field.

Select the RIP version from RIP-1, RIP2-B and RIP2-M.

Multicast Multicast packets are sent to a group of computers on the LAN and are an alternative

to unicast packets (packets sent to one computer) and broadcast packets (packets

sent to every computer).

Internet Group Multicast Protocol (IGMP) is a network-layer protocol used to establish

membership in a multicast group. The AMG1302/AMG1202-TSeries supports IGMP-

v1, IGMP-v2 and IGMP-v3. Select None to disable it.

MLD Proxy Select the version of MLD proxy (v1 or v2) to have the AMG1302/AMG1202-TSeries

act as for this connection. This allows the AMG1302/AMG1202-TSeries to get

subscription information and maintain a joined member list for each multicast group.

It can reduce multicast traffic significantly. Select None to turn off MLD proxy.

ATM QoS

ATM QoS Type Select CBR (Continuous Bit Rate) to specify fixed (always-on) bandwidth for voice or

data traffic. Select UBR With PCR (Unspecified Bit Rate) for applications that are

non-time sensitive, such as e-mail. Select Realtime VBR (real-time Variable Bit

Rate) type for applications with bursty connections that require closely controlled

delay and delay variation. Select Non Realtime VBR (non real-time Variable Bit

Rate) type for connections that do not require closely controlled delay and delay

variation.

Peak Cell Rate Divide the DSL line rate (bps) by 424 (the size of an ATM cell) to find the Peak Cell

Rate (PCR). This is the maximum rate at which the sender can send cells. Type the

PCR here.

Sustain Cell Rate The Sustain Cell Rate (SCR) sets the average cell rate (long-term) that can be

transmitted. Type the SCR, which must be less than the PCR. Note that system default

is 0 cells/sec.

Maximum Burst

Size

Maximum Burst Size (MBS) refers to the maximum number of cells that can be sent at

the peak rate. Type the MBS, which is less than 65535.

PPPoE Passthrough If encapsulation type is PPPoE, select this to enable PPPoE Passthrough. In addition to

the Device’s built-in PPPoE client, you can select this to allow hosts on the LAN to use

PPPoE client software on their computers to connect to the ISP via the device. Each

host can have a separate account and a public WAN IP address.

MTU

MTU The Maximum Transmission Unit (MTU) defines the size of the largest packet allowed

on an interface or connection. Enter the MTU in this field.

For ENET ENCAP, the MTU value is 1500.

For PPPoE, the MTU value is 1492.

For PPPoA and RFC 1483, the MTU is 65535.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZyXEL AMG1302-T series Seite 80

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info