Bedienungsanleitung ZyXEL AMG1302-T series (Seite 114 von 320) (Englisch)

679704

114

Zoom out

Zoom in

Vorherige Seite

1/320

Nächste Seite

Chapter 7 Wireless LAN

AMG1302/AMG1202-TSeries User’s Guide

114

2 Look for a WPS button on each device. If the device does not have one, log into its configuration

utility and locate the button (see the device’s User’s Guide for how to do this - for the AMG1302/

AMG1202-TSeries, see Section 7.6 on page 103).

3 Press the button on one of the devices (it doesn’t matter which). For the AMG1302/AMG1202-

TSeries you must press the WPS button for more than three seconds.

4 Within two minutes, press the button on the other device. The registrar sends the network name

(SSID) and security key through an secure connection to the enrollee.

If you need to make sure that WPS worked, check the list of associated wireless clients in the AP’s

configuration utility. If you see the wireless client in the list, WPS was successful.

7.10.8.2 PIN Configuration

Each WPS-enabled device has its own PIN (Personal Identification Number). This may either be

static (it cannot be changed) or dynamic (in some devices you can generate a new PIN by clicking

on a button in the configuration interface).

Use the PIN method instead of the push-button configuration (PBC) method if you want to ensure

that the connection is established between the devices you specify, not just the first two devices to

activate WPS in range of each other. However, you need to log into the configuration interfaces of

both devices to use the PIN method.

When you use the PIN method, you must enter the PIN from one device (usually the wireless client)

into the second device (usually the Access Point or wireless router). Then, when WPS is activated

on the first device, it presents its PIN to the second device. If the PIN matches, one device sends

the network and security information to the other, allowing it to join the network.

Take the following steps to set up a WPS connection between an access point or wireless router

(referred to here as the AP) and a client device using the PIN method.

1 Ensure WPS is enabled on both devices.

2 Access the WPS section of the AP’s configuration interface. See the device’s User’s Guide for how to

do this.

3 Look for the client’s WPS PIN; it will be displayed either on the device, or in the WPS section of the

client’s configuration interface (see the device’s User’s Guide for how to find the WPS PIN - for the

AMG1302/AMG1202-TSeries, see Section 7.5 on page 101).

4 Enter the client’s PIN in the AP’s configuration interface.

5 If the client device’s configuration interface has an area for entering another device’s PIN, you can

either enter the client’s PIN in the AP, or enter the AP’s PIN in the client - it does not matter which.

6 Start WPS on both devices within two minutes.

7 Use the configuration utility to activate WPS, not the push-button on the device itself.

8 On a computer connected to the wireless client, try to connect to the Internet. If you can connect,

WPS was successful.

If you cannot connect, check the list of associated wireless clients in the AP’s configuration utility. If

you see the wireless client in the list, WPS was successful.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZyXEL AMG1302-T series Seite 114

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info