Bedienungsanleitung ZyXEL Gateway 400 (Seite 32 von 68) (Englisch)

796886

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Gateway 400 User Guide | Configuration

IP Address/Subnet Mask LAN

Two network devices can only communicate with each other if they have a unique name (address).

In IP networks, an IP address is used for this purpose. It ensures that the individual IP packets reach

their proper destination.

The IP Address and the Subnet Mask specified here are used to address the Gateway 400 in the net-

work.

DHCP Server LAN

A DHCP server enables a computer to be fully integrated in an existing network automatically with-

out any further configuration. The computer must only be set to automatically obtain an IP address

(see Chapter 1.4, page 10). The automatic assignment of IP addresses can be restricted to a specific

range of IP addresses (Start IP Address to End IP Address). You can also specify how long the assigned

IP addresses will remain valid. After this time, each computer will be assigned a new IP address. The

assignment of IP addresses is carried out for network devices that are connected via the LAN.

Distribute LAN IPv6 addresses (Router Advertisements activated)

Here you can configure the IPv6 prefix(es) for your home network. The current IPv6 prefix provided

by your ISP is shown under Provider prefix.

If Activate Router Advertisements is enabled but no IPv6 prefix, LAN has been configured, the Pro-

vider prefix supplied by your ISP will be automatically distributed in your network.

If you do not want the Provider prefix to be distributed in the local network, you must ensure that

the option Router Advertisements is disabled.

5.6.1.2 Static Routing

Here you can enter static routes for networks, which can be accessed via the LAN interfaces. Con-

nections to the WAN interface are configured under Internet | Additional Features | Static Routing

(“Static Routing” on page 25).

Click New to open a screen dialog with the following settings:

Name: Any name for the route.

Address Type: IPv4 or IPv6 depending on the address range of the external network.

Destination Network: Address range of the network devices to be reached.

Gateway: Address of the router to the destination network.

Interface: Selection depends on the configured DSL or WAN interface.

Click Save to save the data of the route.

Attention

If you do not have a basic knowledge of network settings, please do not change the de-

fault settings. Any changes to the settings in this screen dialog may cause the Gateway

400 to become inaccessible. If this should happen for some reason, reset the Gateway

400 to its factory settings. Please refer to Chapter 2.3.2, page 15.

Note

Default setting: Start IP Address 192.168.100.50, End IP Address 192.168.100.80. If the

IP address range for the DHCP server is changed, the range of assignable fixed IP ad-

dresses will automatically change as well.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZyXEL Gateway 400 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ZyXEL Gateway 400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info