Bedienungsanleitung ZyXEL LTE3312-M432 (Seite 64 von 202) (Englisch)

730080

Zoom out

Zoom in

Vorherige Seite

1/202

Nächste Seite

Chapter 6 WAN

LTE3302-M432 & LTE3312-M432 User’s Guide

6.5 Network Scan

Use this screen to set how you want the LTE Device to connect to an available mobile network. Click

Network > WAN > Network Scan from the Configuration menu.

Check Interval Type a number of seconds (0 to 99999) to set the time interval between checks. Allow

more time if your destination IP address handles lots of traffic.

Check Timeout Type the number of seconds (0 to 99999) for your LTE Device to wait for a response to the

ping or DNS query before considering the check to have failed. This setting must be less

than the Check Interval. Use a higher value in this field if your network is busy or

congested.

Latency Threshold Type a number of milliseconds (0 to 99999) for the latency threshold.

If the specified latency threshold is exceeded, the LTE Device considers the check to

have failed and makes a new connection after (Latency Threshold * Fail Threshold)

seconds.

Fail Threshold Type how many WAN connection checks can fail (0 to 99999) before the connection is

considered "down" (not connected). The LTE Device still checks a "down" connection to

detect if it reconnects.

Target1/Target2 Select DNS1 to have the LTE Device send a DNS query to the first DNS server address

assigned by the service provider.

Select DNS2 to have the LTE Device send a DNS query to the second DNS server address

assigned by the service provider.

Select Gateway to have the LTE Device ping the WAN interface's default gateway IP

address.

Select Other Host and enter a domain name or IP address of a reliable nearby computer

to have the LTE Device ping that address.

Bridge Select this check box to change the LTE Device’s operating mode to Bridge mode. The

computer connected to the first Ethernet LAN port is allowed to get an individual IP

address from the ISP’s DHCP server directly.

IGMP Select IGMP v1, IGMP v2, IGMP v3 or Auto to enable multicasting. This applies to traffic

routed from the WAN to the LAN.

Select Disable to turn off this feature. This may cause incoming traffic to be dropped or

sent to all connected network devices.

IGMP Proxy This field is available only when IGMP is enabled.

Select this option to have the LTE Device act as an IGMP proxy on this connection. This

allows the LTE Device to get subscribing information and maintain a joined member list

for each multicast group. It can reduce multicast traffic significantly.

IP Type Select IPv4 if you want the LTE Device to run IPv4 only.

Select IPv4/IPv6 to allow the LTE Device to run IPv4 and IPv6 at the same time.

Select IPv6 if you want the LTE Device to run IPv6 only.

Table 16 Configuration > Network > WAN > Management WAN Edit (continued)

LABEL DESCRIPTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZyXEL LTE3312-M432 Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ZyXEL LTE3312-M432

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info