Bedienungsanleitung ZyXEL LTE3316-M604 (Seite 77 von 191) (Englisch)

730079

Zoom out

Zoom in

Vorherige Seite

1/191

Nächste Seite

Chapter 8 Wireless LAN

LTE3316-M604 User’s Guide

8.5 MAC Filter

The MAC filter screen allows you to configure the LTE to give exclusive access to devices (Allow) or

exclude devices from accessing the LTE (Deny). Every Ethernet device has a unique MAC (Media

Access Control) address. The MAC address is assigned at the factory and consists of six pairs of

hexadecimal characters, for example, 00:A0:C5:00:00:02. You need to know the MAC address of the

devices to configure this screen.

To change your LTE’s MAC filter settings, click Configuration > Network > Wireless LAN > MAC Filter. The

screen appears as shown.

Intra-BSS Traffic A Basic Service Set (BSS) exists when all communications between wireless clients or between a

wireless client and a wired network client go through one access point (AP).

Intra-BSS traffic is traffic between wireless clients in the BSS. When Intra-BSS is enabled, wireless

clients can access the wired network and communicate with each other. When Intra-BSS is

disabled, wireless clients can still access the wired network but cannot communicate with each

other.

WMM QoS Check this to have the LTE automatically give a service a priority level according to the ToS

value in the IP header of packets it sends.

WMM QoS (Wifi MultiMedia Quality of Service) gives high priority to voice and video, which

makes them run more smoothly.

Security Mode Select WPA2-PSK, WPA/WPA2 to add security on this wireless network. The wireless clients which

want to associate to this network must have same wireless security settings as this device. After

you select to use a security, additional options appears in this screen. See Section 8.3 on page

70 for detailed information on different security modes. Or you can select Open to allow any

client to associate this network without authentication.

Note: If the WPS function is enabled (default), only Open and WPA2-PSK are

available in this field.

Encryption Select the encryption type of data encryption.

Select AES if your wireless clients can all use AES.

Select TKIP / AES to allow the wireless clients to use either TKIP or AES.

Pre-Shared Key Type a password the wireless stations need to enter to connect to the wireless network.

Group Key

Update Timer

The WPA Group Key Update Timer is the rate at which the AP (if using WPA-PSK key

management) or RADIUS server (if using WPA key management) sends a new group key out to

all clients. The re-keying process is the WPA equivalent of automatically changing the WEP key

for an AP and all stations in a WLAN on a periodic basis. Setting of the WPA Group Key Update

Timer is also supported in WPA-PSK mode. The default setting is 3600 seconds (60 minutes).

Cancel Click Cancel to reload the previous configuration for this screen.

Apply Click Apply to save your changes back to the LTE.

Table 22 Configuration > Network > Wireless LAN > More AP: Edit (continued)

LABEL DESCRIPTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZyXEL LTE3316-M604 Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ZyXEL LTE3316-M604

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info