Bedienungsanleitung ZyXEL LTE3316 Series (Seite 64 von 235) (Englisch)

730078

Zoom out

Zoom in

Vorherige Seite

1/235

Nächste Seite

Chapter 6 Wireless

LTE Series User’s Guide

The following table describes the general wireless LAN labels in this screen.

6.2.1 No Security

Select No Security to allow wireless stations to communicate with the access points without any data

encryption or authentication.

Table 22 Network Setting > Wireless > General

LABEL DESCRIPTION

WiFi Network Setup

Band This shows the WiFi band which this radio profile is using. 2.4GHz is the frequency used by IEEE

802.11b/g/n WiFi clients while 5GHz is used by IEEE 802.11a/ac WiFi clients.

WiFi Click Enable to enable the wireless LAN in this field.

Channel Use Auto to have the Zyxel Device automatically determine a channel to use.

Bandwidth Select whether the Zyxel Device uses a WiFi channel width of 20MHz, 40MHz or 20/40MHz.

A standard 20MHz channel offers transfer speeds of up to 150Mbps whereas a 40MHz channel

uses two standard channels and offers speeds of up to 300Mbps.

40MHz (channel bonding or dual channel) bonds two adjacent radio channels to increase

throughput. The WiFi clients must also support 40MHz. It is often better to use the 20MHz setting in

a location where the environment hinders the

WiFi signal.

Select 20MHz if you want to lessen radio interference with other

WiFi devices in your

neighborhood or the

WiFi clients do not support channel bonding.

Control

Sideband

This is available for some regions when you select a specific channel and set the Bandwidth field

to 40MHz. Set whether the control channel (set in the Channel field) should be in the Lower or

Upper range of channel bands.

WiFi Network Settings

WiFi Network

Name

The SSID (Service Set IDentity) identifies the service set with which a WiFi device is associated.

WiFi devices associating to the access point (AP) must have the same SSID.

Enter a descriptive name (up to 32 English keyboard characters) for the wireless LAN.

Max Clients Specify the maximum number of clients that can connect to this network at the same time.

Hide SSID Select this check box to hide the SSID in the outgoing beacon frame so a station cannot obtain

the SSID through scanning using a site survey tool.

This check box is grayed out if the WPS function is enabled in the Network > Wireless > WPS

screen.

Multicast

Forwarding

Select this check box to allow the Zyxel Device to convert wireless multicast traffic into wireless

unicast traffic.

BSSID This shows the MAC address of the wireless interface on the Zyxel Device when wireless LAN is

enabled.

Security Level

Security Mode Select More Secure (WPA2-PSK) to add security on this WiFi network. The WiFi clients which want

to associate to this network must have the same

WiFi security settings as the Zyxel Device. When

you select to use a security, additional options appears in this screen.

Or you can select No Security to allow any client to associate with this network without any data

encryption or authentication.

See the following sections for more details about this field.

Cancel Click Cancel to restore your previously saved settings.

Apply Click Apply to save your changes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZyXEL LTE3316 Series Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ZyXEL LTE3316 Series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info