Bedienungsanleitung ZyXEL NBG6617 (Seite 72 von 203) (Englisch)

679716

Zoom out

Zoom in

Vorherige Seite

1/203

Nächste Seite

Chapter 10 WAN

NBG6617 User’s Guide

The following table describes the labels in this screen.

Table 21 Network > WAN > Internet Connection: PPPoE Encapsulation

LABEL DESCRIPTION

ISP Parameters for Internet Access

Encapsulation Select PPPoE if you connect to your Internet via dial-up.

IPv4 / IPv6 Select IPv4 Only if you want the NBG6617 to run IPv4 only.

Select Dual Stack to allow the NBG6617 to run IPv4 and IPv6 at the same time.

Select IPv6 Only if you want the NBG6617 to run IPv6 only.

PPP Information

PPP Username Type the user name given to you by your ISP.

PPP Password Type the password associated with the user name above.

MTU Size Enter the Maximum Transmission Unit (MTU) or the largest packet size per frame that

your NBG6617 can receive and process.

PPP Auto Connect Select this option if you do not want the connection to time out.

IDLE Timeout

(second)

This value specifies the time in minutes that elapses before the router automatically

disconnects from the PPPoE server.

PPPoE Service

Name

Enter the PPPoE service name specified in the ISP account.

WAN IP Address Assignment

Get automatically

from ISP

Select this option if your ISP did not assign you a fixed IP address. This is the default

selection.

Use Fixed IP

Address

Select this option and enter your WAN IP address if the ISP assigned a fixed IP address.

DNS Server

First DNS Server

Second DNS

Server

Third DNS Server

Select Obtained From ISP if your ISP dynamically assigns DNS server information (and

the NBG6617's WAN IP address). The field to the right displays the (read-only) DNS

server IP address that the ISP assigns.

Select User-Defined if you have the IP address of a DNS server. Enter the DNS server's

IP address in the field to the right.

Select None if you do not want to configure DNS servers. If you do not configure a DNS

server, you must know the IP address of a computer in order to access it.

WAN MAC Address

The MAC address section allows users to configure the WAN port's MAC address by using the NBG6617’s MAC

address, copying the MAC address from a computer on your LAN or manually entering a MAC address.

Factory default Select Factory default to use the factory assigned default MAC Address.

Clone the

computer’s MAC

address - IP

Address

Select Clone the computer's MAC address - IP Address and enter the IP address of

the computer on the LAN whose MAC you are cloning.

Set WAN MAC

Address

Select this option and enter the MAC address you want to use.

IPv6 Tunneling

Use IPv6 tunneling when the local network uses IPv6 and the ISP has an IPv4 network. When the NBG6617

has an IPv4 WAN address and you set IPv4/IPv6 mode to IPv4 Only, you can enable IPv6 tunneling to

encapsulate IPv6 packets in IPv4 packets to cross the ISP’s IPv4 network.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZyXEL NBG6617 Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ZyXEL NBG6617

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info