Bedienungsanleitung ZyXEL Nebula LTE7461-M602 (Seite 115 von 361) (Englisch)

796991

115

Zoom out

Zoom in

Vorherige Seite

1/361

Nächste Seite

Chapter 7 Broadband

Nebula Mobile Router User’s Guide

115

7.5 Cellular APN

Click Network Setting > Broadband > Cellular APN to display the following screen. Use this screen to

manage the APNs that Zyxel Device is connected to.

Network

Monitoring

Use this field to allow Zyxel Device to try reconnecting to the base station if the cellular

connection is lost. After the third try, the Zyxel Device will reboot to try to reconnect with the base

station. The LED will blink red to indicate that it is rebooting.

Note: This feature only works if there is a previous cellular connection between the

Zyxel Device and the base station.

Proxy ARP Feature

Proxy ARP Enable this to set your Zyxel Device as a server to handle ARP queries from different subnets. The

Zyxel Device will offer Zyxel Device’s own MAC address as an reply.

FQ_Codel Setting

FQ_Codel Select this field to enable FQ_Codel on the Zyxel Device. Clear this field if your network does not

have much real-time traffic.

Use Fair Queuing with Controlled Delay (FQ_Codel) to reduce delays in traffic that could affect

real-time communications, such as video conferencing, live streaming, and voice over Internet

phone calls

FQ_Codel limits traffic throughput, by dropping traffic so as to reduce buffer queuing that causes

delays. It does not prioritize traffic by type.

APN Manual

Mode

Disable this to have the Zyxel Device configure the APN (Access Point Name) of a cellular

network automatically. Otherwise, Click this to enable ( ) and enter the APN manually in the

field below.

APN This field allows you to display the Access Point Name (APN) in the profile.

Enter the Access Point Name (APN) provided by your service provider. Connections with different

APNs may provide different services (such as Internet access or MMS (Multi-Media Messaging

Service)) and charging method.

You can enter up to 64 printable ASCII characters. Spaces are allowed.

Username Enter the user name. You can enter up to 64 printable ASCII characters. Spaces are allowed.

Password Enter the password associated with the user name above. You can enter up to 64 printable ASCII

characters. Spaces are allowed.

Authentication

Type

Select the type of authentication method peers use to connect to the Zyxel Device in cellular

connections.

In Password Authentication Protocol (PAP) peers identify themselves with a user name and

password. In Challenge Handshake Authentication Protocol (CHAP) additionally to user name

and password the Zyxel Device sends regular challenges to make sure an intruder has not

replaced a peer. Otherwise select PAP/CHAP or None.

PDP Type Select IPv4 if you want the Zyxel Device to run IPv4 (Internet Protocol version 4 addressing system)

only.

Select IPv4/IPv6 if you want the Zyxel Device to run both IPv4 and IPv6 (Internet Protocol version 4

and 6 addressing system) at the same time.

Apply Click this to save your changes.

Cancel Click this to exit this screen without saving.

Table 29 Network Setting > Broadband > Cellular WAN (continued)

LABEL DESCRIPTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZyXEL Nebula LTE7461-M602 Seite 115

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info