Bedienungsanleitung ZyXEL NWA1123 (Seite 16 von 305) (Englisch)

729909

Zoom out

Zoom in

Vorherige Seite

1/305

Nächste Seite

Chapter 1 Introduction

NWA/WAC/WAX Series User’s Guide

managed by the NXC (see Section 2.1.3 on page 26). If the Zyxel Device’s radio setting is set to MON

Mode (RF Monitor mode), it will serve as a dedicated RF monitor and its AP clients are disconnected.

The models that do not support MON Mode support Rogue AP Detection (see Section 10.3 on page 109).

Rogue AP Detection allows the AP to scan all channels similar to MON Mode except that the Zyxel

Device still works as an AP while it scans the environment for wireless signals. To see which Zyxel Devices

support the RF Monitor feature, see Section 1.4 on page 19.

The Zyxel Device in MON Mode scans a range of WiFi channels that you specify in a MON Profile, either in

the 2.4 GHz or 5 GHz band. To scan both bands, you need to set both radio 1 and radio 2 in MON Mode.

Once a rogue AP is detected, the network administrator can manually change the network settings to

limit its access to the network using its MAC address or have the device physically removed. If the Zyxel

Device is managed by an NXC, the network administrator can also use Rogue AP Containment through

the NXC.

MON Mode in Standalone Mode

To use an RF monitor in standalone mode, do the following steps:

1 Create a MON Profile in Configuration > Object > MON Profile > Add. Specify a Channel dwell time to

determine how long the RF monitor scans a specific channel before moving to the next one.

2 To scan all 2.4 GHz and 5 GHz channels, select auto in Scan Channel Mode. Make sure that the Activate

check box is selected and click OK.

3 Go to the Configuration > Wireless > AP Management screen and set Radio 1 OP Mode (2.4 GHz) and/or

Radio 2 OP Mode (5 GHz) to MON Mode.

4 Select the Radio 1(2) Profile that you created in the previous step. Make sure that the Radio 1(2)

Activate check box is selected and click Apply.

5 Go to Monitor > Wireless > Detected Device to see a list of APs scanned by the RF monitor.

6 Select an AP or APs in the list and click Mark as Rogue AP or Mark as Friendly AP.

MON Mode in NXC-Managed Zyxel Devices

For NXC-managed Zyxel Devices, do the following steps in the NXC web configurator:

1 Create a MON Profile in CONFIGURATION > Object > MON Profile > Add. Specify a Channel dwell time to

determine how long the RF monitor scans a specific channel before moving to the next one.

2 To scan all 2.4 GHz and 5 GHz channels, select auto in Scan Channel Mode. Make sure that the Activate

check box is selected and click OK.

3 Go to the CONFIGURATION > Wireless > AP Management > Mgmt. AP List > Edit screen and/or set Radio

1 OP Mode (2.4 GHz) and Radio 2 OP Mode (5 GHz) to MON Mode.

4 Select the Radio 1(2) Profile that you created in the previous step. Select Override Group Radio Setting

and click OK.

5 Go to MONITOR > Wireless > Detected Device to see a list of APs scanned by the RF monitor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZyXEL NWA1123 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ZyXEL NWA1123

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info