Bedienungsanleitung ZyXEL VMG8825-Bx0B (Seite 177 von 434) (Englisch)

796882

177

Zoom out

Zoom in

Vorherige Seite

1/434

Nächste Seite

Chapter 7 Wireless

VMG/XMG Series User’s Guide

177

1Ensure that the two devices you want to set up are within wireless range of one another.

2Look for a WPS button on each device. If the device does not have one, log into its configuration utility

and locate the button (see the device’s User’s Guide for how to do this - for the Zyxel Device, see

Section 7.6 on page 162).

3Press the button on one of the devices (it doesn’t matter which). For the Zyxel Device you must press the

WPS button for more than five seconds.

4Within two minutes, press the button on the other device. The registrar sends the network name (SSID)

and security key through a secure connection to the enrollee.

If you need to make sure that WPS worked, check the list of associated wireless clients in the AP’s

configuration utility. If you see the wireless client in the list, WPS was successful.

7.11.8.2 PIN Configuration

Each WPS-enabled device has its own PIN (Personal Identification Number). This may either be static (it

cannot be changed) or dynamic (in some devices you can generate a new PIN by clicking on a button

in the configuration interface).

Use the PIN method instead of the push-button configuration (PBC) method if you want to ensure that

the connection is established between the devices you specify, not just the first two devices to activate

WPS in range of each other. However, you need to log into the configuration interfaces of both devices

to use the PIN method.

When you use the PIN method, you must enter the PIN from one device (usually the wireless client) into

the second device (usually the Access Point or wireless router). Then, when WPS is activated on the first

device, it presents its PIN to the second device. If the PIN matches, one device sends the network and

security information to the other, allowing it to join the network.

Take the following steps to set up a WPS connection between an access point or wireless router

(referred to here as the AP) and a client device using the PIN method.

1Ensure WPS is enabled on both devices.

2Access the WPS section of the AP’s configuration interface. See the device’s User’s Guide for how to do

this.

3Look for the client’s WPS PIN; it will be displayed either on the device, or in the WPS section of the client’s

configuration interface (see the device’s User’s Guide for how to find the WPS PIN - for the Zyxel Device,

see Section 7.5 on page 160).

4Enter the client’s PIN in the AP’s configuration interface.

5If the client device’s configuration interface has an area for entering another device’s PIN, you can

either enter the client’s PIN in the AP, or enter the AP’s PIN in the client - it does not matter which.

6Start WPS on both devices within two minutes.

7Use the configuration utility to activate WPS, not the push-button on the device itself.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZyXEL VMG8825-Bx0B Seite 177

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info