Bedienungsanleitung ZyXEL WAH7601 (Seite 75 von 111) (Englisch)

730076

Zoom out

Zoom in

Vorherige Seite

1/111

Nächste Seite

Chapter 11 WiFi

WAH7601 User’s Guide

3 Press the button on one of the devices (it does not matter which). For the WAH7601 you must press the

WPS button for more than three seconds.

4 Within two minutes, press the button on the other device. The registrar sends the network name (SSID)

and security key through an secure connection to the enrollee.

If you need to make sure that WPS worked, check the list of associated wireless clients in the AP’s

configuration utility. If you see the wireless client in the list, WPS was successful.

PIN Configuration

Each WPS-enabled device has its own PIN (Personal Identification Number). This may either be static (it

cannot be changed) or dynamic (in some devices you can generate a new PIN by clicking on a button

in the configuration interface).

Use the PIN method instead of the push-button configuration (PBC) method if you want to ensure that

the connection is established between the devices you specify, not just the first two devices to activate

WPS in range of each other. However, you need to log into the configuration interfaces of both devices

to use the PIN method.

When you use the PIN method, you must enter the PIN from one device (usually the wireless client) into

the second device (usually the Access Point or wireless router). Then, when WPS is activated on the first

device, it presents its PIN to the second device. If the PIN matches, one device sends the network and

security information to the other, allowing it to join the network.

Take the following steps to set up a WPS connection between an access point or wireless router

(referred to here as the AP) and a client device using the PIN method.

1 Ensure WPS is enabled on both devices.

2 Access the WPS section of the AP’s configuration interface. See the device’s User’s Guide for how to do

this.

3 Look for the client’s WPS PIN; it will be displayed either on the device, or in the WPS section of the client’s

configuration interface (see the device’s User’s Guide for how to find the WPS PIN - for the WAH7601, see

Section 11.5 on page 73).

4 Enter the client’s PIN in the AP’s configuration interface.

5 If the client device’s configuration interface has an area for entering another device’s PIN, you can

either enter the client’s PIN in the AP, or enter the AP’s PIN in the client - it does not matter which.

6 Start WPS on both devices within two minutes.

7 Use the configuration utility to activate WPS, not the push-button on the device itself.

8 On a computer connected to the wireless client, try to connect to the Internet. If you can connect, WPS

was successful.

If you cannot connect, check the list of associated wireless clients in the AP’s configuration utility. If you

see the wireless client in the list, WPS was successful.

The following figure shows you how to set up a wireless network and its security on a WAH7601 and a

wireless client (android 4.4.2 smartphone) by using PIN method.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZyXEL WAH7601 Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ZyXEL WAH7601

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info