Bedienungsanleitung 3Dprintingsystems UP Plus (Seite 43 von 56) (Englisch)

534678

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

UP Plus

3D Printer User Manual

6. M

aintenance

6.1

Changing the Material

To change colours or different materials it’s best to f

head.

There are two ways to do this.

1.) During Printing

a. “3D print

>Maint

old filament and cut the end of the new filament and insert into the extruder head,

then click “Extrude”. Once you see the new filament being extruded click “R

sume” If you find the new filament gets j

the end again and “Extrude”. Note: While paused the extruder and the platform

remains heating. Do not leave unattended.

2.) While idle, click

“3D print >Maintenance” then click

ment. (this t

akes a couple of minutes for the extruder to reach 260c)

beeps, you should be able to remove the filament. Then click “Extrude” and load the new

filament –

cut the end off the new filament before loading.

Always use the

Tube or Straw to feed filament in between the roll guide and extruder head.

Push the filament into the hole at the top of the extruder head, with a little pressure, and the e

truder will automatically extrude material.

should be thin, straight

and smooth.

ter the material weight of the spool so the printer can keep track of material usage.

If the nozzle is blocked, remove the nozzle and clean it.

The extruder and platform are hot. Use gloves when working in this area of

printer.

6.2

Vertical Calibration

This is only recommended to carry out if you find that your models are not vertical.

PORTANT: En

sure your platform is level,

calibration values

before starting this process

The Vertical calibration procedure allows you to ensure that the printer platform is perfectly hor

zontal and that the printer prints consistently in the X, Y and Z

Troubleshooting

3D Printer User Manual

v 2013.6.10

aintenance

Changing the Material

/ colours

To change colours or different materials it’s best to f

irst withdraw the material

There are two ways to do this.

>Maint

enance”

then click “Pause”, then click “Withdraw”, remove the

old filament and cut the end of the new filament and insert into the extruder head,

then click “Extrude”. Once you see the new filament being extruded click “R

sume” If you find the new filament gets j

ammed, do another withdraw and cut

the end again and “Extrude”. Note: While paused the extruder and the platform

remains heating. Do not leave unattended.

“3D print >Maintenance” then click

“Withdraw” to remove the old fil

akes a couple of minutes for the extruder to reach 260c)

beeps, you should be able to remove the filament. Then click “Extrude” and load the new

cut the end off the new filament before loading.

Tube or Straw to feed filament in between the roll guide and extruder head.

Push the filament into the hole at the top of the extruder head, with a little pressure, and the e

truder will automatically extrude material.

The plastic thread is squeezed out

of the nozzle

and smooth.

Then in the maintenance window click “New Spool” and e

ter the material weight of the spool so the printer can keep track of material usage.

If the nozzle is blocked, remove the nozzle and clean it.

The extruder and platform are hot. Use gloves when working in this area of

printer.

Vertical Calibration

This is only recommended to carry out if you find that your models are not vertical.

sure your platform is level,

at the correct height

and you have RESET the

before starting this process

!!!

The Vertical calibration procedure allows you to ensure that the printer platform is perfectly hor

zontal and that the printer prints consistently in the X, Y and Z

direction.

Troubleshooting

from the extruder

then click “Pause”, then click “Withdraw”, remove the

old filament and cut the end of the new filament and insert into the extruder head,

then click “Extrude”. Once you see the new filament being extruded click “R

ammed, do another withdraw and cut

the end again and “Extrude”. Note: While paused the extruder and the platform

“Withdraw” to remove the old fil

Once the printer

beeps, you should be able to remove the filament. Then click “Extrude” and load the new

Tube or Straw to feed filament in between the roll guide and extruder head.

Push the filament into the hole at the top of the extruder head, with a little pressure, and the e

of the nozzle

Then in the maintenance window click “New Spool” and e

ter the material weight of the spool so the printer can keep track of material usage.

The extruder and platform are hot. Use gloves when working in this area of

This is only recommended to carry out if you find that your models are not vertical.

IM-

and you have RESET the

The Vertical calibration procedure allows you to ensure that the printer platform is perfectly hor

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

3Dprintingsystems UP Plus Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info