Bedienungsanleitung 3Dprintingsystems UP Plus (Seite 45 von 56) (Englisch)

534678

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

UP Plus

3D Printer User Manual

6.3 Cleaning the

outside of the

After a lot of printing, the nozzle may be covered with a layer of oxidized

of the nozzle

. When the printer is printing, this oxidized ABS may melt on th

ate discolored spots in the

model. To avoid this you need to regularly clean the nozzle.

Firstly,

move the platform to the bottom, then do a

oxidized ABS.

Lastly, use some heat-

resistant material, like 100

percent cotton cloth or soft paper. A pair of

twee

zers will also be required. Then clip paper or

some other heat-

resistant things with tweezers to

clean up the nozzle.

6.4

Removing / Changing the nozzle

Should the nozzle become blocked, you may need to remove it in order to unblock, or change it. To

remove the nozzle,

first click Withdraw in the maintenance screen, then once the printer is at 260c,

use the nozzle wrench provided in the toolkit that comes

ONLY

remove the nozzle when it is hot

er block.

6.5 Cleaning the

Perfboard

To clean the platform use the included Perfboard pokers, or alternatively use the spatula and

simply just scrape off the surface plastic until

for longer the plastic left in the Perfboard becomes soft and the extruded plastic sticks to it, thus

not requiring the holes of the Perfboard to be empty/clean.

6.6

Lubrication of bearings

The bearings on the UP 3D

Printer may occasionally require a bit of lubrication to keep it opera

ing smoothly. The recommended grease to use is lithium grease. When lubricating the bearings,

first clean off as much old grease as possible from the bearings, and then apply

If the nozzle is blocked, remove the nozzle and clean it.

The extruder and platform are hot. Use gloves when working in this area of

printer.

Troubleshooting

3D Printer User Manual

v 2013.6.10

outside of the

nozzle

After a lot of printing, the nozzle may be covered with a layer of oxidized

black

ABS

. When the printer is printing, this oxidized ABS may melt on th

e nozzle, and may cr

model. To avoid this you need to regularly clean the nozzle.

move the platform to the bottom, then do a

“Withdraw” in order to

heat the nozzle to melt the

resistant material, like 100

percent cotton cloth or soft paper. A pair of

zers will also be required. Then clip paper or

resistant things with tweezers to

Removing / Changing the nozzle

Should the nozzle become blocked, you may need to remove it in order to unblock, or change it. To

first click Withdraw in the maintenance screen, then once the printer is at 260c,

use the nozzle wrench provided in the toolkit that comes

with your UP Printer.

remove the nozzle when it is hot

, trying to remove it while cold will damage the extru

Perfboard

To clean the platform use the included Perfboard pokers, or alternatively use the spatula and

simply just scrape off the surface plastic until

smooth on both sides. If you preheat the

for longer the plastic left in the Perfboard becomes soft and the extruded plastic sticks to it, thus

not requiring the holes of the Perfboard to be empty/clean.

Lubrication of bearings

Printer may occasionally require a bit of lubrication to keep it opera

ing smoothly. The recommended grease to use is lithium grease. When lubricating the bearings,

first clean off as much old grease as possible from the bearings, and then apply

If the nozzle is blocked, remove the nozzle and clean it.

The extruder and platform are hot. Use gloves when working in this area of

printer.

Troubleshooting

ABS

on the outside

e nozzle, and may cr

model. To avoid this you need to regularly clean the nozzle.

heat the nozzle to melt the

Should the nozzle become blocked, you may need to remove it in order to unblock, or change it. To

first click Withdraw in the maintenance screen, then once the printer is at 260c,

, trying to remove it while cold will damage the extru

To clean the platform use the included Perfboard pokers, or alternatively use the spatula and

smooth on both sides. If you preheat the

platform

for longer the plastic left in the Perfboard becomes soft and the extruded plastic sticks to it, thus

Printer may occasionally require a bit of lubrication to keep it opera

ing smoothly. The recommended grease to use is lithium grease. When lubricating the bearings,

first clean off as much old grease as possible from the bearings, and then apply

new grease to the

The extruder and platform are hot. Use gloves when working in this area of

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

3Dprintingsystems UP Plus Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info