554031
17
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
6-17
6.5 How do I connect the other contacts in the ABUS wireless alarm system?
6.5.1 Connecting a wired sounder
The ABUS wireless alarm system is fitted with a built-in sounder. If required, an external sounder or piezo sounder can be
connected to alert inhabitants and neighbours with a loud signal during the alarm.
To connect an external sounder:
Connect the external cables to the sounder clamps (+ Bell) (Bell -). Make sure that the polarity is correct if you are
connecting an electronic sounder and/or polarised sounders.
Select the sound signal to be generated (see chapter 8, page 8-29, Quick Key [1][2][32] in the installer menu) for
each sounder.
For a loudspeaker or built-in sounder driver, the ABUS wireless alarm system generates a continuous or
interrupted oscillating voltage.
For a sounder or electrical sounder, the ABUS wireless alarm system generates a continuous 9V DC or a slow
pulsing voltage, depending on the alarm type. Use a sounder with a maximum power consumption of 9V 500mA.
!
WARNING:
To avoid interference to the external sounder loop if no connection is made to the sounder clamps, connect one of
the 2.2 k resistors supplied between the (+ Bell) and (Bell -) terminals.
NOTE:
It is very important to define the menu item Sounder / LS in the installer menu correctly. The setting depends on
the type of sounder. You normally select the Sounder setting.
If the sounder output is overloaded (max. 500 mA) and it is silenced, you have to interrupt the load at the output for
at least 10 seconds before reconnecting a load to the output. The circuit-breaker is then reset.
6.5.2 Sounder tamper
If a sounder tamper contact is fitted, connect the tamper contact of your (wired) sounder with the tamper input on the PC board of
the
ABUS wireless alarm system (Bell TMP / COM). This line is protected from tampering by a 2.2 k resistor. This should be
connected in series to the contact inside the sounder housing.
The tamper input is monitored only if the setting in the installer menu is set to “Yes” under “External Device” (Quick Key [1] [2] [31]
in the installer menu). For more information, see [1] [2] [31].
6.5.3 Controllable relay and transistor outputs
Your ABUS wireless alarm system has 4 controllable outputs (2 x 24V DC 3A relays potential-free or 13.8V 200mA and 2 x 13.8V
DC 70mA transistors). These outputs are activated according to system events. For example alarms, system faults, specific zone
and partition events, but also user-controlled or time-controlled.
Connect switch outputs
UO1 (switch output 1) and UO2 (switch output 2) as follows:
AUX
UO2 / UO1
N.O C N.C
+
-
J4 (UO2)
or
J5 (UO1)
NEG
EXTERNAL
POWER
UO2 / UO1
N.O C N.C
+
-
J4 (UO2)
or
J5 (UO1)
1 PIN
Only
Positive: Connect the collective
clamp “COM/BLK” and N.C (9V
from NC) with an external
device you want to control via
this switch output. Take note of
jumper J4 (for UO2) and J5 (for
UO1). (See number 15 on page
5-14: What is what inside the
system?)
Negative: Connect the
collective clamp “AUX/RED”
and N.C (9V from AUX) with an
external device you want to
control via this switch output.
Take note of jumper J4 (for
UO2) and J5 (for UO1). (See
number 15 on page 5-14: What
is what inside the system?)
Potential-free: Connect clamps c and
N.C with an external power supply and
an external device you want to control
via this switch output. Take note of
jumper J4 (for UO2) and J5 (for UO1).
(See number 15 on page 5-14: What is
what inside the system?)
+9V
+9V
COM
UO2 / UO1
N.O C N.C
+
-
J4 (UO2)
or
J5 (UO1)
POS
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Abus FU9000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Abus FU9000

Abus FU9000 Installationsanweisung - Deutsch - 96 seiten

Abus FU9000 Bedienungsanleitung - Deutsch - 55 seiten

Abus FU9000 Bedienungsanleitung - Englisch - 56 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info