Bedienungsanleitung ACP ACE19 (Seite 7 von 15) (Englisch)

660219

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Programming

What is stage

cooking?

Stage cooking enables

several different cooking cycles, or

stages, to be used consecutively

without repeated input from the user.

Stage cooking can be set to defrost

food initially, then cook it, and then

keep the food warm until serving time.

Programming

Preheat Setting

The convection temperature setting

can be set between 150°F to 475°F

(65°C to 250°C). It is recommended

to set the preheat setting to the most

commonly used temperature for that

oven. The factory default preheat

setting is 475°F (250°C).

To program the preheat setting:

1. Turn oven on to set preheat.

2. Press Program Save pad.

3. Press Temp Entry pad.

4. Enter desired temperature by

using the numeric key pads.

• Temperature must be entered

in 5°F (5°C) increments. If

not, the temperature will

automatically change to the

nearest 5°F (5°C).

5. Preheat temperature is changed.

Programming Multiple Stages

Stage cooking allows consecutive cooking cycles without interruption.

Up to four different cooking cycles can be programmed into a memory pad.

To use stage cooking:

1. Follow steps 1 through 6 above.

7. Press Stage pad.

• This will begin programming for the next cooking

stage.

• Display indicates stage to be programmed.

• Enter cook time, temp and power level as in steps 4. 5 and 6.

• To enter another cooking stage for that pad, press Stage pad

again.

• Up to four different stages can be programmed.

8. Press Program Save pad to save the program and

changes.

9. To discard changes, press Stop/Reset pad before

pressing Program Save pad.

Programming Pads

Oven is shipped from the factory for single digit programming. To change

the oven default to double digit programming, see User Option section. To

program the amount of time, power level, or temperature setting for a pad:

1. Oven must be ON.

• Press Preheat On/Off pad.

• Oven Preheating 475°F or 250°C shows in display

with Oven Preheating ashing.

2. Oven reaches preheat temperature.

• Ready 475°F or 250°C shows in display with Ready ashing.

Press Program Save pad.

• Programming mode begins.

• Enter Program to Add/Review: shows in display.

3. Press pad to be programmed or reprogrammed.

• Display will change to review all settings for the pad.

• The pad number that is being programmed displays beside the word

ITEM.

4. Press Time Entry pad to program amount of cooking time.

• Enter desired cooking time by using numeric key pads.

• The total microwave cooking time (all stages combined) is

20 minutes.

5. Press Temp Entry pad to program the cooking temperature.

• Enter desired convection temperature by using numeric

pads.

6. Press Power Level pad to program level of microwave

power.

• For a lower microwave power, press pads 1 (for 10%)

through 9 (for 90%). 0 turns off the microwave power

and cooking is by convection only.

• Press any numeric key pad twice to set power level back to 100%.

7. Press Program Save pad to save the program changes.

8. To discard changes, press Stop/Reset pad.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ACP ACE19 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ACP ACE19

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info