Bedienungsanleitung Acronis Backup PC 11.5 Update 6 (Seite 109 von 248) (Englisch)

624431

109

Zoom out

Zoom in

Vorherige Seite

1/248

Nächste Seite

Be careful! To be on the safe side, it is advisable to assign unique names to the volumes.

The Linux-style bootable media shows local disks and volumes as unmounted (sda1, sda2...).

Changing volume properties

Size and location

When recovering a volume to a basic MBR disk, you can resize and relocate the volume by dragging it

or its borders with a mouse or by entering corresponding values in the appropriate fields. Using this

feature, you can redistribute the disk space between the volumes being recovered. In this case, you

will have to recover the volume to be reduced first.

Note: Volumes backed up using the sector-by-sector option cannot be resized.

Tip: A volume cannot be resized when being recovered from a backup split into multiple removable media. To be

able to resize the volume, copy all parts of the backup to a single location on a hard disk.

Type

A basic MBR disk can contain up to four primary volumes or up to three primary volumes and

multiple logical drives. By default, the program selects the original volume's type. You can change

this setting, if required.

 Primary. Information about primary volumes is contained in the MBR partition table. Most

operating systems can boot only from the primary volume of the first hard disk, but the number

of primary volumes is limited.

If you are going to recover a system volume to a basic MBR disk, select the Active check box.

Active volume is used for loading an operating system. Choosing active for a volume without an

installed operating system could prevent the machine from booting. You cannot set a logical

drive or dynamic volume active.

 Logical. Information about logical volumes is located not in the MBR, but in the extended

partition table. The number of logical volumes on a disk is unlimited. A logical volume cannot be

set as active. If you recover a system volume to another hard disk with its own volumes and

operating system, you will most likely need only the data. In this case, you can recover the

volume as logical to access the data only.

File system

By default, the recovered volume will have the same file system as the original volume has. You can

change the volume's file system during recovery, if required.

Acronis Backup can make the following file system conversions: FAT 16 -> FAT 32 and Ext2 -> Ext3.

For volumes with other native file systems, this option is not available.

Assume you are going to recover a volume from an old, low-capacity FAT16 disk to a newer disk.

FAT16 would not be effective and might even be impossible to set on the high-capacity hard disk.

That's because FAT16 supports volumes up to 4 GB, so you will not be able to recover a 4 GB FAT16

volume to a volume that exceeds that limit, without changing the file system. It would make sense

here to change the file system from FAT16 to FAT32.

Older operating systems (MS-DOS, Windows 95 and Windows NT 3.x, 4.x) do not support FAT32 and

will not be operable after you recover a volume and change its file system. These can be normally

recovered on a FAT16 volume only.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Acronis Backup PC 11.5 Update 6 Seite 109

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Acronis Backup PC 11.5 Update 6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info