Bedienungsanleitung Acronis Snap Deploy 4 (Seite 138 von 145) (Englisch)

624427

138

Zoom out

Zoom in

Vorherige Seite

1/145

Nächste Seite

that the target volume number is the same as the volume number

specified with the

/partition

parameter.

/start:<start sector>

Sets the start sector for deploying a volume to the unallocated space

on the hard disk.

/size:

<volume size in

sectors>

Sets the new size of the volume in sectors. The size of a sector is

considered to be 512 bytes, regardless of the physical sector size on

the hard disk drive.

For example, if you want the volume size to be 512 MB (a megabyte is

1 048 576 bytes), specify the size as follows:

/size:1048576

Specify this size even if you are using a hard disk drive with 4-KB

sectors.

To see the size of the volume in the master image, use the /list

command.

/fat16_32

Enables the file system conversion from FAT16 to FAT32 if t

he volume

size after deployment is likely to exceed 2 GB. Without this parameter,

the deployed volume will inherit the file system from the image.

/restore_bootable:<aut

o|on|off>

Sets the rule of deployment for the master boot record (MBR) when

deploying a volume (when deploying a disk, MBR is always deployed):

 auto

: Deploy the MBR only when deploying an active volume that

contains an operating system. Use this setting to ensure that the

operating system can boot.

 on: Deploy the MBR when deploying any acti

ve volume, no matter

whether the volume contains an operating system or not.

 off

: Do not deploy the MBR. Use this setting, for example, to

preserve the Unix boot loader.

/type:<active|primary|

logical>

Sets the deployed volume to active, primary or logical

, if possible (for

example, there cannot be more than four primary volumes on a disk).

Setting a volume to active always sets it to primary, but a volume that

is set to primary may remain non-active.

If the type is not specified, the software tries to keep

the target

volume type. If the target volume is active, the deployed volume is set

to active. If the target volume is primary and there are other primary

volumes on the disk, one of them will be set to active, and the

deployed volume becomes primary. If n

o other primary volumes

remain on the disk, the deployed volume is set to active.

When deploying a volume to unallocated space, the software extracts

the volume type from the image. For a primary volume, the type will

be set as follows:

 If the target disk

is the first according to BIOS and it has no other

primary volumes, the deployed volume will be set to active.



If the target disk is the first according to BIOS and there are other

primary volumes on it, the deployed volume will be set to logical

 If the ta

rget disk is not the first according to BIOS, the deployed

volume will be set to logical.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Acronis Snap Deploy 4 Seite 138

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Acronis Snap Deploy 4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info