Bedienungsanleitung ACV HP300 (Seite 36 von 118) (Englisch, Holländisch, Französisch)

677361

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

3. The required diameter per string of the electric system wire with 3 strings is: 2.5 mm2 – 4 mm2,

depending on performance as described on the data table.

The wires adequate for connection to the electric system are the following:

Adequate type: H0 5VVF

H0 5RRF

Connection with wire protection tube is not allowed.

4. The connection wire and the wire with green/yellow colour mark have to be connected in the terminal

block. The plastic wire driver marked with a label located at the lower part of the cover of the fitting house has

to be broken out. (“Break out for connection”) The overhang part of the rubber wire driver, which is placed in

the bag attached to the appliance, has to be cut, then the wire driver has to be stitched to the electric system

wire. The connection wire has to be connected in the terminal block of the left side according to phase label (L,

N, ). The wire fixing and the bent clamp have to be tightened finally, then the wire driving rubber has to be

fitted to the lower horizontal surface of the cover frame in a way that it has to protect electric parts against any

possible water inflow, after mounting the cover.

Figure 7.4.-1. shows the electric connection diagram of the hot water tank, which can also bee seen on the

cover of the fitting house.

Figure 7.4.-1.

IT IS FORBIDDEN TO OPERATE THE HOT WATER TANK WITHOUT ANY PROTECTIVE EARTHING.

The protective earthing has to comply with the instructions of the Hungarian Standard IEC 60364.

7.5. First start up

Before first start up of the appliance, please, check the following elements:

 Adequate installation of the appliance;

 Adequate connection of water pipes and electric wires;

 The leaking of cooling pipe has been tested;

 Efficient water discharge pipe.

 Full insulation protection;

 Adequate earthing;

 Adequate power source;

 No obstacle to air inlet and air outlet;

 There is no air in the water pipeline and all the valves are in open position;

 Efficient electric leak protection is operating;

 Water inlet pressure is sufficient(≥0,15MPa)

After being connected to the water pipeline system and the electric power system, the hot water tank has

to be filled up with water from the household water supply system. The tank must be filled up with water

before switching on the heating. During filling the tank up with water, open the hot water valve of the closet

tap while keep all the other valves closed. Then open the closing valve mounted in the cold water pipe (Figure

7.3-1., item No. 1. ). The tank is filled up when water appears on the tap. For flushing purposes, the water must

be flown for some minutes, then you can close the valve of the hot water.

PLEASE TURN TO A TECHNICIAN TO CHECK THE FIRST HEATING.

Perform an eye check to decide whether connections of edges and pipe fittings are leaking or not – and

tighten them carefully, if necessary. The appliance can be connected to the electric power system only after this

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ACV HP300 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info