771227
48
Zoom out
Zoom in
Vorherige Seite
1/54
Nächste Seite
WaterMaster 25 - 35 - 45 - 70 - 85 - 120 : A1006482 - 664Y7300 • D
en
46
EN
FR
NL
ES
IT
DE
PL
RU
MAINTENANCE
TORQUE VALUES Tightening torque
(Nm)
Description Min. Max
Burner ange screws 5 6
Electrode screws 3 3.5
CLEANING THE EXCHANGER
Set-up conditions
Water heater shut down
External power supply isolated
Gas supply closed
Burner removed i.a.w. procedure “Removal and Installation of the Burner on page 44.
Front and top panels open, refer to “Removal and Installation of the Front and Top Panels” on page
39.
Procedure
1. Brush and vacuum clean the chamber.
2. Pour some water in the chamber to ush away any foreign deposits that may be present in the heat
exchanger.
3. Remove and clean the condensate trap.
4. Reinstall the condensate trap, refer to Water heater preparation on page 37.
Follow-on tasks
1. Reinstall the burner according to procedure “Removal and Installation of the Burner” on page 44.
2. Restart the water heater in accordance with procedure “Restarting after Maintenance” on page 46.
RESTARTING AFTER MAINTENANCE
Set-up conditions
All removed components reinstalled
All connections made
Power supply
Gas supply open
Hydraulic circuits full of water
Procedure
1. Make sure there is no gas leak at the gas connections.
2. Switch the appliance on using the ON/OFF master switch.
3. Set the appliance at maximum power and check the absence of gas leaks.
4. Check the gas pressure and CO2 adjustment in accordance with “Checking and Adjusting the Burn-
er” on page 42.
Follow-on tasks
None
1
12
3
2
3
WaterMaster® 25 - 35 - 45 WaterMaster® 70 - 85 - 120
REMOVAL, CHECK AND INSTALLATION OF THE BURNER ELECTRODE
Set-up conditions
Water heater shut down
External power supply isolated
Gas supply closed
Front and top panels open, refer to “Removal and Installation of the Front and Top Panels” on page
39.
Removal procedure
1. Disconnect the electrode grounding cable from the electrode.
2. Disconnect the electrode ignition cable from the electrical box.
3. Remove two mounting screws (1) and retain them for reinstallation.
4. Remove the electrode (2) and the gasket (3).
5. Check the correct alignment of the electrode ends and that the gap corresponds to the values
indicated on the gure below.
6. If the electrode is in bad condition, replace it.
Installation procedure
1. Install a new gasket (3).
2. Install the electrode (2) using the two screws (1), torque i.a.w. Torque Values” on page 46.
Follow-on tasks
1. Reconnect the grounding cable to the electrode.
2. Reconnect the ignition cable to the electrical box.
Essential recommendations for the correct operation of the appliance
Remove the electrode to control it in case of ignition problems.
Min. 3 mm
Max. 4 mm
48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für ACV Watermaster wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von ACV Watermaster

ACV Watermaster Bedienungsanleitung und Installationsanweisung - Deutsch - 48 seiten

ACV Watermaster Bedienungsanleitung und Installationsanweisung - Holländisch - 52 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info