Bedienungsanleitung Adler AD 4813 (Seite 8 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

799984

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

unplug the power cable.

18. Before operating the device check if all parts and accessories are properly mounted to

avoid poor grinding performance and knife and cutting plate blunting.

19. Use only original accessories supplied with the meat grinder and shredder.

20. Do not overload the device with excess product or shoving the product in too hard. Use

only the pusher for shoving the product in. Using other object can damage the meat grinder

and shredder.

22. The meat to be ground should be free of bones, gristles, tendons or veins. Cut the

bigger parts into pieces.

23. Do not cover the ventilation holes in the housing while the device is on.

24. Do not grind dry poppy seed. The poppy seed needs to be steamed and soaked before

grinding.

25. Store the device out of the reach of children.

Description of product: meat grinder with shredder AD4813 – picture A

1. Food pusher for meat grinder 2. Tray

3. Button of grinding chamber 4. Store box

5. Knob 6. Motor unit

7. Motor gear nest 8. Grinding chamber

9. Worm gear 10. Cross cutting blade

11. Kebbe attachment 12. Sausage attachment

13. Nut 14. Cutting plate (Ø 7mm hole)

15. Cutting plate (Ø 5mm hole) 16. Cutting plate (Ø 3mm hole)

17. Shedding blade for fine cutting 18. Shedding blade for coarse cutting

19. Slicing blade 20. Food pusher for shredding

21. Shredder head

Before first use

1. When carrying the device be sure to hold the housing with both hands. Do not carry the device only by the tray (2) or grinding chamber

(8).

2. Do not fix the cutting plate (14, 15 or 16) when using kebbe attachments (11). Look at picture B1.

3. Do not grind hard food such as bones, nuts and hard fibers such as ginger. Look at picture B2.

Assembling of meat grinder

1. Press the grinding chamber button (3), hold the grinding chamber (8) and insert it into the motor gear nest (7). When inserting please

pay your attention the grinding chamber (8) must be slanted. Look at picture 1.

2. Then move the grinding chamber (8) anticlockwise so that the grinding chamber (8) being fastened tightly. Look at picture 2.

3. Place the worm gear (9) into the grinding chamber (8), long end first, and turn to feed the screw slightly until it is set into the motor gear

nest (7). Look at picture 3.

4. Place the cross cutting blade (10) onto the worm gear (9) shaft with the blade facing the front. Look at picture 4. If the cross cutting

blade (10) is not fitted proper side, the meat will not be grinded.

5. Place a suitable cutting plate (14, 15 or 16) over the shaft of the worm gear (9), aligning the tabs with both slots. Look at photo 5.

6. Support or press the center of the cutting plate with one finger then screw the nut (13) tight with another hand. Look at picture 6. Do not

over tighten.

7. Place the tray (2) on the top of the grinding chamber (8) and fix it into position. Look at picture 7.

8. Locate the unit on a firm, stable surface.

9. The air passage at the bottom and the side of the motor housing should be kept not blocked.

Meat grinder operation

1.Cut all foods into pieces (sinewless, boneless and fatless meat is recommended, approximate size: 50 mm x 50 mm x 50 mm), so that

they fit easily into the tray (2) opening.

2.Turn the knob (5) to "ON" position, the device begin to work.

3.Put the food on the tray (2). Use the food pusher (1) to moving the food. Look at picture 7.

4.After use, turn the knob (5) to “OFF” position and unplug it from the power supply.

Reverse function

1.If the device is clogging, turn the knob (5) to "OFF" position, and then turn the knob to reverse "REV" position, the worm gear (9) will run

reverse direction.

After the termination of jam, release the reverse button “REV”.

2. If the device is still clodded by food, switch off the device and pull out the plug, then clean out the food being inside the grinding

chamber (8).

3. ALWAYS rotate the knob (5) from “ON” position to “REV” reverse speed or from “REV” reverse speed position to “ON”, if the previous

working conditions stop the motor for more than 5 seconds.

4. If the device is clogging, switch off the device immediately. If the device not stopped, the overheating of motor will happened and the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 4813 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info