Bedienungsanleitung Adler AD 7855 (Seite 5 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

800043

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste

bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may

effect the environment. Do not dispose this appliance in the common waste bin.

5. The wet cooling button (F) lowers the temperature of the air by running the water pump. Press the button (F) when there is water in

water tank ONLY. Additionally, a set of two plastic containers (12) is attached. Plastic containers (12) should be filled by cold, tap water

and do not exceed maximum level. Next, put them on several hours inside the freezer. Then put one or both of containers into water

tank (8). To blow the wet cool air, the device must be filled with water. When the device is operating, periodically check the water level to

see whether to add water. Press button (F) again to turn off the wet cold air blowing.

corresponding icons on the panel will light up.

6. Pressing the oscillation button (C) starts the oscillation of device that provide even distribution of cold air stream in range 55° in left

and right direction. The corresponding indicator turn on.

7. The TIMER button (E) allows for programming the amount of operation time with 1 hour decrements from 1 to 8 hours.

Water Consumption: 300 ml / hour

Noise level: 59dB

Airflow volume: 800m3/h

Tank capacity: 2 liters

Product dimensions: 30 x 30 x 108 cm

Power: 60 W

TECHNICAL DATA:

Battery: CR2025 (3V)

Power supply 220-240V ~50 Hz

Power Max: 320 W

6. Cover the device by plastic bag to protect the dust and coil the power cord. Storage in dry place out of direct sunlight.

c) Sleep Mode: was designed to use the effects of Nature Mode to fall asleep. It will gradually decrease the speed of the fan in 30

minute increments:

CLEANING AND MAINTENANCE

* When choose the low fan speed: the fan will run the same as low speed Nature Mode.

4. Drain the water before seasonal storage by removing the water tank (chapter Using the Device - point 2). Use mild soap and water to

clean the water tank. Then dry the device and water tank completely to avoid the moisture damage.

9. All buttons on remote control (14) have got same functions as buttons on control panel (2). Do not place any objects between the

device and the remote control to ensure proper communication between the remote control and the device. To start remote control

(14) operation pull out the installing film. To replace the battery push the release tab on remote control housing. Replace with a

battery of the same type, refit the battery in reverse order.

c) Put the filter (5) and the cover with net (7) back in place and tighten the screws.

* When choose the high fan speed: the fan will blow 30 minutes at high speed Nature Mode, next it will switch for 30 minutes at medium

speed Nature Mode, then it will switch to low speed Nature Mode.

* When choose the low fan speed: the fan will blow 5 seconds at low speed and then switch off for 5 seconds, this cycle will be repeated

again and again.

* When choose the middle fan speed: the fan will blow 5 seconds each speed: medium, low, medium, stop, low, medium, low, stop and

this cycle will be repeated again and again.

* When choose the high fan speed: the fan will blow 5 seconds each speed: medium, low, high, medium, high, low, high, stop and this

cycle will be repeated again and again.

a) Normal Mode: allows the user to manually adjust the speed of fan between high, medium and low. Each time the fan is turned on it will

start operation on normal mode.

* When choose the middle fan speed: the fan will blow 30 minutes at medium speed Nature Mode then switch to low speed Nature

Mode.

REMARK: If you prefer a constant fan speed whilst sleeping, we recommend setting the fan to Normal Mode and selecting speed as low.

Use the timer function to set the fan to switch off after an elapsed time (e.g. 1 hour after going to bed).

8. The MODE button (D) allows for changing between one of 3 blowing modes:

Always unplug the device before you start to clean or water empty the device.

1. Clean with soft, dry cloth. Do not use chemical solvents because they can cause permanent damage or deformation of the device.

2. If the device is not used for three or more months, take the batteries out of the remote control.

a) Unplug the device, remove screw (6) of the back housing by screwdriver and then take the cover with net (7) and filter (5) out.

3. After long time operation, the cover with net (7) and filter (5) will be clogged with the dust, which will greatly affect the device’s

performance of cooling. If long time no changing water, there may be mold and mildew. We suggest to clean the cover with net (7)

and filter (5) once a week. The filter clean procedure is as below:

b) Nature Mode: mimics the natural wind action by repeating the fan speed sequence:

d) Make sure the water tank (8), the filter (5) and the cover with net (7) are replaced in correct position before switching on again. Before

seasonal storage make sure all parts are dry by running the fan mode for 2 hours or shorter if sure the filter (5) is dry completely.

normal wind, nature wind and sleep wind.

b) Wipe clean or clean using a vacuum cleaner. Use the duster it gently dust off the filter (5). Then rinse the filter (5) under fresh water to

remove dust and dirty. The cover with net (7) should not be rub with hands to avoid net deformation.

5. Drain the water from the plastic containers (12) before storage.

Adler AD 7855 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info