Bedienungsanleitung Adler AD 7924 (Seite 7 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

800051

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Troubleshooting

1) Trouble: Do not work.

The protective device will work in the following cases:

2. If the plug has been removed, after restarting the device will return to the original mode, TIMER ON and TIMER OFF - must be set again.

If the device runs in cooling “K” or dry “L” mode with door or window opened for a long time when relative humidity is above 80%, dew may

drip down from the outlet.

1. Restarting the device immediately after stopping work or changing the selected mode while working, you must wait 3 minutes.

REMARK: there is condensing water recycling hidden within this unit. The condensing water is partly kept recycling between the condenser

and the water plate. When the water level rises to the upper level, the float switch and water full indicator (E4) lights on to remind draining

water. Please cut off the power supply, move the appliance to a suitable place, remove the drain plug, drain water completely. After the

drain, re-install the plug, or the appliance may leak and make your room wet. Drain pipe is added to kit, with inner diameter 9mm, outer

diameter 12mm, material: PVC.

2. The compressor will stop after running 8 minutes, then run again after 6 minutes.

1. The up centrifugal fan will run at low speed, and the speed can't be adjusted.

COOLING "K" mode:

- When the room temperature ＜24 ℃, the unit will automatically select high fan speed mode "M..".

DEHUMIDIFYING "L" mode:

1. When the room temperature is higher than set temperature on control panel, the compressor starts to run.

2. When the room temperature is lower than set temperature on control panel, the compressor stop and upper fan operates at original set

speed.

Fan "M." mode.

1. The up centrifugal fan runs at set speed, and the compressor does not run. .

3. The device adopts constant temperature dehumidifying mode, and the adjustment of temperature is no effective.

The main control board has memory function, when the device is ready to run but in stop status, the main control board can memorize the

initialization of working mode. When you turn on the unit, it will work as the same enactment of working-mode as last time, no need to reset

the working mode again. (This condition is not available when the unit is under AUTOMATIC mode "J".)

2. The adjustment of temperature is no effective.

Notice:

Timer operation "N":

REMOTE CONTROLLER

To operate the device, aim the remote controller (4) at the signal receptor (3). The remote controller will operate the device at distance 5

meters when pointing at signal receptor of the device.

PROTECTIVE DEVICES

4. To prevent environmental pollution, take out the used batteries and dispose safety and appropriately.

The protective device may trip and stop the appliance in the cases listed below:

3. For long time no use, take out the batteries.

2. at cooling mode: room temperature is below 15°C (59°F)

2. Put the batteries inside the slot, must be corresponding to the signs of "+" and "-" on the remote control.

Sleeping mode "I" operation:

3. at dehumidifying mode: room temperature is below 15°C (59°F).

1. Slide the back cover to open and take off the isolating film on the batteries.

2. Press “N” button to set Automatic On time while the unit is ready.

1. Press “N” button to set Automatic Off time while the unit is running.

1. at cooling mode: indoor air temperature is over 43°C (109°F)

3. The time can be adjusted within a range of 1 hour to 24 hours by pressing the button "D"（+）or "E"（-）.

1. The sleeping mode operations when the unit is under cooling "K" mode.

2. Press the button "I" in cooling mode "K" , then the unit will work under sleeping mode and the up centrifugal fan will turn to low speed

automatically. The set temperature will increase by 1 ℃ after one hour, and increase 2℃ after two hours. After six hours the unit will stop

running.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 7924 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info