Bedienungsanleitung Adler AD 7924 (Seite 8 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

800051

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

d) air outlet or intake is blocked.

Analysis:

b) maybe in close distance there is another appliance heat-working like heater or lamp, etc.

b) to avoid water leakage, please locate the device on flat ground.

5) Trouble: Do not work and water full indicator "E4"

Analysis:

a) drain the condensate before moving.

c) maybe batteries in the remote controller are exhausted.

a) if the set temperature is close to room temperature, you can lower the set temperature.

b) maybe air outlet is blocked by obstacle. Take the obstacle away.

a) maybe door or window are open.

3) Trouble: Works but not cools

f) set temperature is too high.

a) pull out rubber plug to drain water.

2) Trouble: works for a short time only

4) Trouble: Water leak during moving.

Analysis:

a) maybe the protector trip or fuse is blown, please wait for 3 minutes and start again, protector device may be preventing device from

working.

Analysis:

c) the air filter is dirty, please clean it.

d) maybe the plug is not properly plugged in.

10) Trouble: LED displays failure code "E3"

Device maintenance

b) maybe plug or socket damages. Replace by service provider.

c) maybe fuse broken. Replace the fuse by service provider (specification: 3,15A/250VAC).

a) timing shut down or set temperature reached. Restart it or wait for auto-switch.

Analysis:

11) Trouble: LED displays failure code "E4"

a) room temperature sensor fails or damages. Replace the room temperature sensor by service provider.

Troubleshooting

a) maybe not plugged. So, plug in it.

Analysis:

b) if it is often in this state, please contact qualified service technical.

Analysis:

a) room temperature is lower than set temperature. It is a normal phenomenon, the machine will auto-switch while the room temperature is

higher than the set temperature.

6) Trouble: Device fails to start up.

Analysis:

8) Trouble: no cold air under COOL "K" mode.

b) Device enters into anti-frost protection. The device will auto switch after anti-frost protection is over.

9) Trouble: LED displays failure code "E2"

a) the evaporator oil pipe sensor fails or damaged. Replace the evaporator coil pipe sensor by service provider.

7) Trouble: Device automatically stops.

Analysis:

a) water-full warning. Drain out the water.

CLEANING AND MAINTENANCE

Analysis:

1. Turn off the device first before disconnecting from power supply.

It is necessary to clean the air filter every 2 weeks if the device operates in an extremely dusty environment. Clean as follows:

1. Stop the device first, push up the air filter (Picture F).

Air filter maintenance

3. If the dirt is conspicuous, wash it with a solution of detergent in lukewarm water. After cleaning dry it in a shaded and cool place, then

reinstall it.

2. Wipe with a soft and dry cloth. Use lukewarm water below 40C to clean if theappliance is very dirty.

2. Clean and reinstall the air filter.

3. Never use volatile substance such as gasoline or polishing powder to clean the device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 7924 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info