Bedienungsanleitung Aeg-electrolux cf 260 (Seite 34 von 100) (Deutsch, Englisch, Holländisch, Portugiesisch, Spanisch)

361847

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

4.2 Selecting the Cup Measure

0 Repeatedly press the "Cup Measure"

key (Fig. 3, d) until the desired cup

symbol is indicated.

The cup measures are indicated as fol-

lows:

Espresso cup

Coffee cup

Coffee mug

The coffee machine is factory-set to

standard measures.

Notes on changing the cup measures

can be found in „Changing and Saving

the Cup Measure" Page 35.

4.3 Dispensing Coffee

Refer to „Dispensing Coffee" Page 33.

5 Frothing Milk

The steam can be used to froth milk

and to heat liquids. Since a higher

temperature is needed to produce

steam than to make coffee, the coffee

machine has an additional steam

mode.

To make a cappuccino, fill a large cup

1/2 to 2/3 full with espresso, and then

add the frothed milk.

Caution! Danger of scalding when the

steam nozzle is activated! Hot water or

steam output can cause scalding. Do

not activate the steam nozzle until it is

immersed in the milk.

0 To produce steam, press the "Steam

Pre-selector" key (Fig. 3, g) . The

indicator illuminates, and at the same

time, the "Coffee machine heating"

indicator (Fig. 3, i) flashes. When the

heating process is finished, this indica-

tor changes from flashing to con-

stantly on. The coffee machine is now

ready for frothing milk.

If the steam function is left unused for

more than 1 minute, the coffee

machine automatically changes back

to coffee-making mode.

0 Pour approximately 100 ml cold,

skimmed or semi-skimmed milk into a

small, narrow jug (max. 0.5 l capacity).

This must be small enough to fit under

the steam nozzle.

The milk should be cold. You should

also use a cold jug, and not rinse this

with hot water.

0 Swivel the steam nozzle out and hold

the jug under the steam nozzle so that

the end is completely immersed in the

milk. Turn the Selection dial for steam

and hot water (Fig. 1, D) to the

position (Fig. 17). The milk is now

frothed up.

Hold the jug steady duing the frothing

process. The nozzle should not be

allowed to touch the bottom of the

jug, since this would prevent the steam

escaping. Froth the milk until the vol-

ume has at least doubled.

0 To stop frothing, turn the Selection dial

for steam and hot water (Fig. 1, D) to

the position and remove the jug

(Fig. 17).

Caution! Danger of scalding from hot

milk spray! Switch the steam off,

before removing the jug with the

frothed milk.

0 To finish steam mode, press the "Steam

Pre-selector" key (Fig. 3, g) . The

indicator goes out.

The coffee machine is now ready for

making coffee again.

0 Each time you have frothed milk, let

off some hot water through the nozzle

for a short time by setting the Selec-

tion dial for steam and hot water (Fig.

1, D) to the position. This is nec-

essary to prevent milk residues drying

inside the nozzle, and thereby blocking

it. Use a suitable container to catch the

water.

0 Remove the frothing aid after each use

(Fig. 18) and flush the milk residues

away under running water. Wipe the

steam nozzle off with a damp cloth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aeg-electrolux cf 260 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info