Bedienungsanleitung AEG EM 50-2 (Seite 7 von 12) (Deutsch, Englisch)

648392

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Operation

EM 50-2 is equipped with an easily operated encoder button (turn

and press) and a display which describes the current situation. The

display is backlit and is illuminated by pressing the encoder button

(OK). The illumination is automatically switched o after 30 seconds.

Press the encoder button and the main menu will be shown on the

display.

Turn the button to scroll through the options. Not all the options are

shown on the display at once, but they can be accessed by turning

the encoder button.

Press OK to select a highlighted option.

ZONE 1 OFF

ZONE 2 OFF

SENSOR 1 ##.#°C

SENSOR 2 ##.#°C

MOIST 1 NO

MOIST 2 NO

OUT. TEMP ##.#°C

ALARM NO

SHOW INFO

SETUP

RESTART

EXIT

Main menu

Display texts

ZONE 1 OFF

Heating zone 1 active (ON) or inactive (OFF)

ZONE 2 OFF

Heating zone 2 active (ON) or inactive (OFF)

SENSOR 1 ##.#°C

Sensor 1 (heated sensor) core temperature.

Applies only when GROUND SENSOR sensor is

connected. NOTE: Not ambient temperature!

SENSOR 2 ##.#°C

Sensor 2 (heated sensor) core temperature.

Applies only when GROUND SENSOR sensor is

connected. NOTE: Not ambient temperature!

MOIST 1 NO

Sensor 1 moisture status. YES / NO / Blank.

Blank will be shown if temperature is above Set

Temp or the system is in Afterrun mode.

MOIST 2 NO

Sensor 2 moisture status. YES / NO / Blank.

Blank will be shown if temperature is above Set

Temp or the system is in Afterrun mode.

OUT TEMP ##.#°C

Ambient outdoor temperature. Applies only

when ETF sensor is connected.

ALARM NO

Fault message, fault type will be displayed. Red

LED on front of unit will ﬂash.

SHOW INFO

Application info

APP: E. 1-ZONE

Application type: electric heating

SW VERSION 1.10

Software version

SENSOR 1 GRND

Sensor type, sensor 1

SENSOR 2 OFF

Sensor type, sensor 2

SENSOR ATF OFF

ATF 5 sensor connected

EXIT

Return to main menu

Settings

Please note that incorrect sensor setup may lead to poor or lacking

ice and snow melting.

Press OK and a submenu will be shown on the display.

Select the parameter to be set and press OK.

SETUP

FORCE HEAT OFF

Manual start of forced heat. Press OK and select

ON to start Forced heat.

EM 50-2 controller will heat in the pre-pro-

grammed afterrun time, see AFTERRUN 1and 2.

SELECT SCALE C

Whether temperature is to be displayed in Cel-

sius (C) or Fahrenheit (F) can be selected here.

Select the required scale and press OK. Press

OK to return to the SETUP menu.

SET TEMP 1 3.0C

Set temperature for Zone 1: The temperature

at which the ice and snow melting system will

become active can be set here. The temperature

setting can be adjusted from +50 / -20°C

(122 / -4°F). Set the required temperature and

press OK.

SET TEMP 2 3.0C

Set temperature for Zone 2: The temperature

at which the ice and snow melting system will

become active can be set here. The temperature

setting can be adjusted from +50 / -20°C

(122 / -4°F). Set the required temperature and

press OK.

OFF TEMP 1 OFF

he lowest operating temperature for Zone 1 can

be set here. Below this tempera ture, the system

will enter standby mode. The adjustment range

goes down to -20°C/OFF (-3.9°F/OFF). OFF = no

limit. To change the minimum cut-o tempera-

ture, press OK, turn the encoder button to the

desired value and conﬁrm with OK.

OFF TEMP 2 OFF

The lowest operating temperature for Zone 2 can

be set here. The adjustment range goes down

to -20°C/OFF (-3.9°F/OFF). OFF = no limit. To

change the minimum cut-o temperature, press

OK, turn the encoder button to the desired value

and conﬁrm with OK.

AFTERRUN 1 2:00

Afterrun time Zone 1 : An afterheat duration of

between 0 and 18 hours can be set here. The

system will continue to provide heat for the

speciﬁed time after the moisture/temperature

signal has been eliminated by a heating cycle.

Use the encoder button to set the required after-

run time and press OK.

AFTERRUN 2 2:00

Afterrun time Zone 2 : An afterheat duration of

between 0 and 18 hours can be set here. Use

the encoder button to set the required afterrun

time and press OK.

OFFSET T1 0.0C

Zone 1 temperature can be calibrated here. With

EF 50-25 H sensor, the temperature shown on

the EM 50-2 display is always the core tempera-

ture of the sensor. For calibration, please see

page 13.

EM 50-2 English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG EM 50-2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AEG EM 50-2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info