Bedienungsanleitung AEG HG654440SM (Seite 26 von 64) (Holländisch)

551909

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

8. INSTALLATION

WARNING!

Refer to the Safety chapters.

WARNING!

The following instructions about

installation, connection and

maintenance must be carried out

by qualified personnel in compli-

ance with standards and local

regulations in force.

8.1 Gas Connection

It is necessary that the connection to the

gas mains are carried out by means of an

AGB tap. Choose fixed connections or

use a flexible pipe in AGB (stainless

steel) in compliance with the regulation

in force. If you use flexible metallic

pipes, be careful they do not come in

touch with mobile parts or they are not

squeezed. Also be careful when the hob

is put together with an oven.

The connection must be done according

to regulation NBN D 5I.003.

Make sure that the gas supply

pressure of the appliance obeys

the recommended values. The

adjustable connection is fixed to

the comprehensive ramp by

means of a threaded nut G 1/2".

All the components shown in the

figure have already been assem-

bled in the factory. The appli-

ance, before leaving the factory,

has been tested in order to give

you the best results.

ABC

End of shaft with nut

Washer

Elbow

Flexible nonmetal pipes

connection:

If it is possible to easily control the con-

nection in its full area, you can use a flex-

ible pipe. Tightly attach the flexible pipe

by clamps.

Liquid gas: use the rubber pipe holder.

Always engage the gasket. Then contin-

ue with the gas connection. The flexible

pipe is prepared for apply when:

– it can not get hot more than room

temperature, higher than 30°C;

– it is no longer than 1500 mm;

– it shows no throttles;

– it is not subject to traction or torsion;

– it does not get in touch with cutting

edges or corners;

– it can be easily examined in order to

check its condition.

The control of preservation of the flexi-

ble pipe consists in checking that:

– it does not show cracks, cuts, marks of

burnings on the two ends and on its

full length;

– the material is not hardened, but

shows its correct elasticity;

– the fastening clamps are not rusted;

– expired term is not due.

If one or more defects are visible, do not

repair the pipe, but replace it.

When installation is complete,

make sure that the seal of each

pipe fitting is correct. Use a

soapy solution, not a flame!

8.2 Injectors replacement

Remove the pan supports.

Remove the caps and crowns of the

burner.

With a socket spanner 7 remove the

injectors and replace them with the

ones which are necessary for the

type of gas you use (see table in

"Technical Information" chapter).

Assemble the parts, follow the same

procedure backwards.

Replace the rating plate (it is near

the gas supply pipe) with the one for

the new type of gas supply. You can

www.aeg.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG HG654440SM Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AEG HG654440SM

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info