Bedienungsanleitung AEG HG654440SM (Seite 27 von 64) (Holländisch)

551909

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

find this plate in the package sup-

plied with the appliance.

If the supply gas pressure is changeable

or different from the necessary pressure,

you must fit an applicable pressure ad-

juster on the gas supply pipe.

8.3 Adjustment of minimum

level

To adjust the minimum level of the burn-

ers:

Light the burner.

Turn the knob on the minimum posi-

tion.

Remove the knob.

With a thin screwdriver, adjust the

by-pass screw position.

The by-pass screw

• If you change from natural gas G20/

G25 20/25 mbar to liquid gas, fully

tighten the by-pass screw in.

• If you change from liquid gas to natu-

ral gas G20/G25 20/25 mbar, undo the

by-pass screw approximately 1/4 of a

turn (1/2 of a turn for Triple Crown

burner).

WARNING!

Make sure the flame does not go

out when you quickly turn the

knob from the maximum position

to the minimum position.

8.4 Electrical connection

• Ground the appliance according to

safety precautions.

• Make sure that the rated voltage and

type of power on the rating plate

agree with the voltage and the power

of the local power supply.

• This appliance is supplied with a mains

cable. It has to be supplied with a cor-

rect plug, able to support the load

marked on the rating plate. The plug

has to be fitted in a correct socket.

• Any electrical component must be in-

stalled or replaced by the Service

Force Centre technician or qualified

service personnel.

• Always use a correctly installed shock-

proof socket.

• Make sure that there is an access to

the mains plug after installation.

• Do not pull the mains cable to discon-

nect the appliance. Always pull the

mains plug.

• The appliance must not be connected

with an extension cable, an adapter or

a multiple connection (risk of fire).

Check that the ground connection is

in conformity with the standard and

regulations force.

• The power cable must be placed in

such a way that it does not touch any

hot part.

• Connect the appliance to the mains

with a device that lets to disconnect

the appliance from the mains at all

poles with a contact opening width of

minimum 3 mm, eg. automatic line

protecting cut-out, earth leakage trips

or fuse.

• None of a parts of the connection ca-

ble can not get a temperature 90 °C.

The blue neutral cable must be con-

nected to the terminal block label with

"N". The brown (or black) phase cable

(fitted in the terminal block contact

marked with "L") must always be con-

nected to the live phase.

8.5 Replacement of the

connection cable

To replace the connection cable use on-

ly H05V2V2-F T90 or equivalent type.

Make sure that the cable section is appli-

cable to the voltage and the working

temperature. The yellow/green earth

wire must be approximately 2 cm longer

than the brown (or black) phase wire.

ENGLISH 27

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG HG654440SM Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AEG HG654440SM

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info