Bedienungsanleitung Aeris A300 CS (Seite 8 von 64) (Englisch)

618071

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

A300 CS OPERATING MANUAL

GAS 1 DIVE

PSI

380

SURF

0:11

CHANGE

BATTERY

BATT

GAS 1 DIVE

PSI

850

SURF

1:03

TMT 1

LOW BATTERY

BATT

POWER SUPPLY

• A300 CS Battery >> (1) 3 vdc, CR2, Lithium, 800 mAh - Duracell, Energizer, Panasonic, or RayOvac recommended.

• Use life (examples) >> 15 hours at 100% Brightness with Auto Dim set off; 34 hours at 60% Brightness with Auto Dim To

time set for 10 seconds and Dim level set for 10%. Refer to page 62 for more information relating to power usage.

Once a low battery alarm condition occurs (red icon ﬂashing), sufﬁcient time should be available to

ascend to the surface while Brightness is held to 60% maximum.

• Transmitter Battery (each) >> (1) 3 vdc, CR2, 800 mAh, Lithium.

• Use life >> 300 dive hours if (2) 1 hour dives per dive day.

• Replacement >> by user (annual recommended).

POWER SAVER MODE (PSM)

When 2 minutes elapse without any button being pressed while on the surface, the unit will enter a Power Saver Mode (PSM)

which turns the display screen off until a button is pressed at which time it will turn back on.

During the time that the screen is off, all operations continue as normal in the background with current updated information

displayed as soon as the screen comes on again.

An Auto Dim feature can also be used to save power during dives by dimming the display screen to a % level of Brightness that

you set prior to the dives. Refer to pages 13 and 62.

BATTERY STATUS

To access, while viewing the Home Menu when on the surface >>

• S (< 2 sec) to access Home Setup Menu, then -

• A or M (< 2 sec) until BATT, TMT STATUS is highlighted (Fig. 5).

• S (< 2 sec) then activates the unit's receiver, then the Status screen appears (Fig. 6).

Note that a color coded BATT icon is displayed at the upper/left of Surface and Dive Main screens as an indication of status.

• Green = good, meaning you have sufﬁcient battery power to conduct normal diving activities.

• Yellow = caution (warning), meaning you should have sufﬁcient battery power to complete a normal 1 hour dive.

• Red (while on the surface) = alarm, meaning the battery must be changed prior to starting a dive.

• Red (during a dive) = alarm, meaning you should savely ascend to the surface and replace the battery before continuing

with diving activities. Caution - The unit may shut off at any time without further warning.

LOW BATTERY WARNING

• The BATT icon will change from green to yellow when voltage decreases to 2.75 vdc.

• Battery change prior to any diving is recommended. Less than 1 hour dive time may be expected.

• The graphics LOW BATTERY will alternate with NORM (or GAUG or FREE) on the Surface Main (Fig. 7).

• If a dive is started, the graphic is not displayed on the dive mode screens.

• Brightness level will be limited to 60% with other functions continuing as usual.

LOW BATTERY ALARM

• The BATT icon will change from yellow to red (ﬂashing) when voltage decreases to 2.50 vdc.

• Entry into dive modes and compass use is blocked. Battery change is required prior to starting any dives.

• The graphics CHANGE BATTERY will ﬂash on the Surface Main (Fig. 8A) until the battery is changed or the unit shuts off.

• If a dive is in progress, the red BATT icon will ﬂash and the graphics GO UP LOW BATTERY will be displayed red with 2 Up

Arrows (Fig. 8B) that will alternate with the usual information displayed until on the surface.

Ascent should be made to the surface following proper ascent protocols (respecting ascent speeds

allowed, and Deco and Safety Stops if possible).

TRANSMITTER (TMT) BATTERY STATUS

Indication is provided only while on the surface.

Low Battery Warning

• The graphics BATT LOW appear solid (yellow) on the Status screen (see Fig. 6).

• DC functions continue to be available (surface and dive).

Low Battery Alarm

• The graphics TMTx LOW BATTERY (red) alternate with the graphics NORM (or GAUG) on the SURF Main screen (Fig. 9).

• The graphics BATT LOW (red) also ﬂash on the Status screen.

• TMT operation continues until Tank Pressure decreases to 50 PSI at which time the TMT's link is lost.

Fig. 5 - HOME SETUP MENU

(to access Battery Status)

Fig. 6 - BATTERY STATUS

Fig. 7 - A300 CS

LOW BATTERY WARNING

Fig. 8A - LOW BATTERY

ALARM (on surface)

SETUP MENU

SET DATE , TIM E

BAT T, TMT STAT US

BLUETOOTH

SET AU TO D I M

BATT, TMT STATUS

A30 0 C S =

TMT

1 =

TMT 2 =

TMT 3 =

TMT

4 =

BAT T G O OD

NOT AVA IL

BAT T LO W

OFF

BAT T G O OD

GAS 1 DIVE

PSI

850

SURF

1:03

LOW

BATTERY

BATT

Fig. 9 - TMT LOW BATTERY

ALARM

GAS 1 ATR

PSI

1320 36

BATT

GO UP

LO W BAT T E R Y

Fig. 8B - LOW BATTERY

ALARM (during dive)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aeris A300 CS Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info