Bedienungsanleitung Aeta Scoopy plus S (Seite 113 von 136) (Englisch)

782361

113

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

SCOOPY+ S - User Manual

107

6.2. Using the remote html access

This service allows to access the html pages of the codec from remote.

What you need on the SCOOPY+ S:

 Up-to-date firmware (1.09 minimum).

 The "Remote access" option.

 Internet access, for instance via an Ethernet connection to a LAN. But other IP connections are

suitable as well: mobile data access …

The control device can be any device with a web browser (no need to install any application): computer,

tablet or even a smartphone…

6.2.1. Step 1: connect the SCOOPY+ S to the server

First you must connect the codec to the AETA server so that it is accessible. To protect the access to the

unit, you can define a "codec password" that allows to get control over it.

Note: as a security measure, a password that is blank or too short is not accepted by the system (see

more on this topic in 6.3, Security aspects).

Menu Tools > Maintenance > Remote Access: activate "Remote Access".

In the same menu, you can select the IP interface that the codec will use for connecting to the service:

"Network Interface". For using always the same interface as for AoIP transmission, select "Auto".

To check the successful connection: menu Tools > About, "Remote Access Status".

If you want to change the password, go to the menu Tools > Maintenance > Remote Access, Codec

Password. The following rules apply to this password:

 The password must be at least 8 characters long. For safety, it is recommended to use at least

13 characters, with a combination of uppercase and lowercase letters, numbers, and special

characters among the following: _ - + * . : , ; # ? ! = .

 If you enter a blank password, or one with less than 8 characters, a random password is

automatically generated by the SCOOPY+ S.

Variation: you can also use the "REMOTE ACCESS" html page for this step:

Maintenance tab, REMOTE ACCESS page, check "Allow Remote Access".

On the same page, you can select the IP interface that the codec will use for connecting to the service:

"Network Interface". For using always the same interface as for AoIP transmission, select "Auto".

To check the successful connection: STATUS page, GENERAL section.

You can change the password, with following rules:

 The password must be at least 8 characters long. For safety, it is recommended to use at least

13 characters, with a combination of uppercase and lowercase letters, numbers, and special

characters among the following: _ - + * . : , ; # ? ! = .

 If you enter a blank password, or one with less than 8 characters, a random password is

automatically generated by the SCOOPY+ S.

6.2.2. Step 2: open the remote session

The SCOOPY+ S to be controlled must be connected to the server, and you must know the serial number

and the "Codec password" of the unit.

Open a web browser, and go to the following URL:

https://cloud.aeta.com/rac

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aeta Scoopy plus S Seite 113

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info